Question about Yamaha DT 125 R Motorcycles

1 Answer

Yamaha DTR 125cc - Sputtering when wet (rain, jetwash etc.)

What I've done.... -Changed Spark Plug -Cleaned Carburetor -Cleaned Air Filter -Waterproofed Electrics (WD40) Bike starts first time without choke. Sputters at mid range rpm and loses power. Seems to be letting in the water somewhere. after allowing the bike to dry out for a while, all seemed ok except the engine revving high. with the engine turned off and in first gear, the bike rolls back, then locks, then rolls back, locks again etc....(bike should not roll at all in gear.) Also, there is a Led on the speedometer which I think indicates the engine temperature and this is lit up red. I've checked my coolant level which was empty at the time so now have topped up and light is still on?? I know this sounds like a lot of problems but I'm hoping there's a simple/cheap solution and I appreciate any help.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Yamaha Master
  • 39,960 Answers

Hi, Nick_krywiuk for more information about your question and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
https://yamahaclub.com/forums/topic/31400-sputter-sputter
Kawasaki ER 5 POWER LOSS
http://www.motogelnar.cz/manual/YAMAHA/DT125X_RE-05-Service_Manual.pdf
OEM parts for Yamaha
http://www.dt125.cz/download/Owners_Manual-DT125X_RE.pdf

Posted on Mar 14, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

voodoomox
  • 1689 Answers

SOURCE: can i put 2002 yamaha dtr engine 125cc in a 1995 dtr 125cc bike?

well at first in wont fit because the cooling (LC) system will not fit the 02, but with a little welding and some alum works, you will be able to fit it.

the only difference will be the placing of the mount, weld holes and drill holes on the frame, but before you do so, remove all electric components from the frame.

hope this helps.

Posted on May 24, 2009

  • 6 Answers

SOURCE: bike loses power in the mid rpm range

Try the air filter first (make sure it's clean). The needle valve on your carb slider could be bent, or not seated correctly or just set wrong. If you have a power exhaust valve, it could be set wrong or malfunctioning as well. Good luck.

Posted on Jun 25, 2009

  • 3567 Answers

SOURCE: MY 125cc 4 STROKE JUST CUT OUT FOR NO REASON, AND

Even though I am unfamiliar with your bike I will give this a try on the condition that You give me a "Helpful" rating or better. Like you, I am unable to comprehend pigeon English.

A spark plug can go bad at any time. Get a new plug. Put the wire on the plug then ground the metal side of the plug against the cylinder head as you press the starter button. Look for the spark. If no spark, check the side stand kill switch. It kills the engine so that you don’t start out with the side stand down. If broken or out of adjustment, it would kill the spark. Check for a broken wire at the side stand switch and coupler. Try moving the kill switch by hand. If that doesn’t work then wire a jumper around the switch to bypass it. Check the fuses. How good is the battery? Is the handlebar kill switch on? Check the operation of the ignition switch and all kill switches with a volt ohmmeter.

Posted on Jul 06, 2009

  • 69 Answers

SOURCE: Yr 2000 thundercat, won't idle unless choke fully on

First thing I would try is some sea foam, you can get it pretty much at any auto parts store...put it in the tank per instructions on the bottle, if the carbs are gummed/dirty... seafoam is you best hope at getting them clean without pulling them.

If sea foam doesnt work, you'll have to yank the carbs, but before you do... pull the tank, set it backwards where the seat was, get about a two foot fuel line (air line works just fine) run it ti the tank and start the bike, take a can of starting fluid (WD 40 works too but stinks when it starts to burn off afterwards) and spray around the base of the outside of the carbs where the boots connect it to the intake, if the engibe revs, you have a leak...cracked boot probably.

If no leaks are detected... then yank the carbs, pull the bowl covers and start cleaning....also, while you have them off pull the slide covers off and check the diaphrams on the needle for rips or cracks as well.

Check/clean.. put everything back together... if it still isnt running right then I have no other suggestions... certainly sounds like an air/fuel problem... if were anything else choking it wouldn't make it better.

Posted on Jul 10, 2009

  • 1 Answer

SOURCE: Hi I've gota DTR 125 54 model Bike was rev high

i got the same problem with my dt 125, it got high rev even if i pull the spark plug cap free from the spark plug it keeps on reeving, it will just stop if i pull the choke on, any smart ideas please? im all out of it,

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yamaha vity starting


Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Fuel line to carburetor or throttle body pinched or kinked.
8. Carburetor float stuck.
9. Fuel injectors clogged.
10. Severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
11. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
12. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and CDI box.
Spark plug cables in bad condition and shorting check for leakage in the dark, cable connections loose, or connected to the wrong cylinders.
13. Ignition timing incorrect due to a faulty MAP, CKP, O2, TPS, sensors.
14. Faulty neutral, clutch lever, or kickstand safety switch.
15. Faulty fuel pump or fuse or relay.
16. Faulty CDI box.
17. A stuck bent or burnt valve.
18. Tip over sensor needs a reset.
19. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Yamaha vity 125 starting problem
Yamaha vity 125cc http://www.49ccscoot.com/manuals/Yamaha_Vino_125_Service_Manual.pdf
OEM parts for Yamaha
YAMAHA VITY XC125E Owner Manual

Jun 28, 2014 | 2006 Yamaha Vino 125

1 Answer

Sputtering in 1st and 2nd gear on YZ 85


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system, carburetor and/or filter.
12. Old dead or bad fuel.
13. Fuel tank vent system plugged or carburetor vent line closed off.
14. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
15. Carburetor controls misadjusted.
16. Damaged carburetor.
17. Incorrect valve timing.
18. Weak or broken valve springs.
19. Damaged intake or exhaust valve.
20. Check for engine trouble codes
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Dirt Rider Magazine
KDXRIDER NET View topic Sputtering in 1st and 2nd
YAMAHA YZ85 Owner Service Manual
OEM parts for Yamaha
YAMAHA YZ85 Owner Manual

Dec 27, 2013 | 2005 Yamaha yZ 85

1 Answer

Why is my 2009 Yamaha 650 Vstar sputtering when accelerating at mid to high speed?


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system, carburetor and/or filter.
12. Old dead or bad fuel.
13. Fuel tank vent system plugged or carburetor vent line closed off.
14. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
15. Carburetor controls misadjusted.
16. Damaged carburetor.
17. Incorrect valve timing.
18. Weak or broken valve springs.
19. Damaged intake or exhaust valve.
20. Check for engine trouble codes
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Yamaha 650 star sputtering high speeds
http://www.starbikeforums.com/forums/18-engine-work/5238-engine-bogs-past-1-4-throttle.html
Yamaha XVS650 Service Manual
OEM parts for Yamaha
YAMAHA XVS650 Owner Manual

Sep 10, 2013 | Yamaha XVS 650 Dragstar Classic...

1 Answer

My 2003 Yamaha 1100 v star runs great around town but when cruising at highway speeds it sputters and misfires. While accelerating from cruising speed, the sputtering goes away,however when I quit...


Hi, Al and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking.
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Intake air leak.
10. Water, dirt, or rust in the fuel system, carburetor and/or filter.
11. Fuel tank vent system plugged or carburetor vent line closed off.
12. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
13. Carburetor controls misadjusted.
14. Damaged carburetor.
15. Incorrect valve timing.
16. Weak or broken valve springs.
17. Damaged intake or exhaust valve.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
totalmotorcycle com
http://www.kawasakimotorcycle.org/forum/kawasaki-cruisers/145028-help-miss-cruising-speed-2.html
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2000/LIT-11626-13-36_96.pdf

Aug 18, 2013 | 2003 Yamaha V Star 1100 Classic

1 Answer

My ttr 90 is spitting and sputtering when you give it gas and i cleaned the carb multiple times and i cleaned the spark plug and put a new air filter in ?


Hi, Austin and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system, carburetor and/or filter.
12. Old dead or bad fuel.
13. Fuel tank vent system plugged or carburetor vent line closed off.
14. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
15. Carburetor controls misadjusted.
16. Damaged carburetor.
17. Incorrect valve timing.
18. Weak or broken valve springs.
19. Damaged intake or exhaust valve.
20. Check for engine trouble codes
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
ttr 90 carb issues TTR
Idles good but sputters when gas it
YAMAHA TTR90 Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-tt-owners-manuals

Mar 31, 2013 | 2005 Yamaha TTR 90 E

1 Answer

Yamaha r6 sputtering


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Intake air leak.
10. Water, dirt, or rust in the fuel system, carburetor and/or filter.
11. Old dead or bad fuel.
12. Fuel tank vent system plugged or carburetor vent line closed off.
13. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
14. Carburetor controls misadjusted.
15. Damaged carburetor.
16. Incorrect valve timing.
17. Weak or broken valve springs.
18. Damaged intake or exhaust valve.
19. Check for engine trouble codes
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
R6 sputtering through rpm range
http://www.r6messagenet.com/forums/r6-maintenance-technical/56256-bike-sputtering.html
2008 2009 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Jul 05, 2012 | Yamaha YZF-R6 Motorcycles

1 Answer

R6 sputtering out


Hi, Clubsareus and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Intake air leak.
10. Water, dirt, or rust in the fuel system, carburetor and/or filter.
11. Old dead or bad fuel.
12. Fuel tank vent system plugged or carburetor vent line closed off.
13. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
14. Carburetor controls misadjusted.
15. Damaged carburetor.
16. Incorrect valve timing.
17. Weak or broken valve springs.
18. Damaged intake or exhaust valve.
19. Check for engine trouble codes
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
R6 sputtering through rpm range
http://www.cycleforums.com/forums/51-cycle-angels/107985-help-my-r6-sputtering.html
2006 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Jan 28, 2012 | 2006 Yamaha YZF-R6

1 Answer

Yamaha majesty 125 2004 won't start! The engine


Hi, Mlt1937 and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. A severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
13. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
14. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
15. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
16. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
17. Faulty neutral, clutch lever, or kickstand safety switch.
18. Faulty fuel pump or fuse or relay.
19. A stuck bent or burnt valve.
20. Tilt sensor needs a reset.
21. Security system not disarming alarm needs a reset.
22. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Scooter Troubleshooting Scooter won start All about Scooters
The Ultimate GY6 Starter Ignition Troubleshooting Tutorial
Yamaha YP125 YP250 YP400 repair manual Download Manuals Technical $10 cheap
http://www.49ccscoot.com/manuals/Yamaha_Vino_125_Service_Manual.pdf Free
OEM parts for Yamaha
YAMAHA MAJESTY YP125E Owner Manual

Apr 23, 2017 | 2007 Yamaha Majesty 125

1 Answer

SPUTTERING ON A 2006 YAMAHA V STAR CLASSIC


Hi, Amendina280 and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking.
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Intake air leak.
10. Water, dirt, or rust in the fuel system, carburetor and/or filter.
11. Fuel tank vent system plugged or carburetor vent line closed off.
12. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
13. Carburetor controls misadjusted.
14. Damaged carburetor.
15. Incorrect valve timing.
16. Weak or broken valve springs.
17. Damaged intake or exhaust valve.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Yamaha 650 star sputtering high speeds
http://www.starbikeforums.com/forums/49-v-star/9084-v-star-acting-very-sluggish-sputtering.html
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Sep 25, 2010 | 2006 Yamaha V Star Classic

2 Answers

No spark on yamaha dtr 125cc


Sounds like you are flooding the engine with gas. Put in a new spark plug then twist the throttle one time to prime the cylinder. Now get your hands off the throttle and give it a few kicks. Each time you twist the throttle the power valve gives a shot of gas. Too much can flood the engine quickly.

May 17, 2010 | 2000 Yamaha DT 125 R

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...