Question about 1998 Honda CBR 1100 XX Super blackbird

Open Question

Remove coolant reservoir super blackbird

Got a leak around the coolant reservoir somewhere. howis it held in position so i can checkthe connecting pipes.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Coolant reservoir empty after sitting overnight


Check the water pump and see if coolant is around it.

Jul 26, 2015 | Cars & Trucks

1 Answer

Coolant reservoir empty when sitting overnight


You must have a coolant leak. If there are no signs of a leak, you may have a gasket on the engine that has gone bad, and the coolant is being pushed out the exhaust system. The coolant expands when hot and cools when the engine cools. During the cooling stage the cooling system creates a suction on the coolant in the reservoir and draws enough coolant back into the system to keep it full. Apparently you are loosing enough coolant somewhere that the reservoir can not fill the system before going dry.

Jul 26, 2015 | 1998 Ford Windstar

1 Answer

Loses water from resevoir but not from radiator


So the level keeps dropping in the reservoir? If you have to keep adding coolant to the reservoir, the system is leaking or losing coolant somewhere. Have the system pressure tested to find the leak. Is the reservoir itself leaking? When the level gets low enough, first the reservoir will go dry, then the radiator level will start to drop.
Here's how the reservoir works: coolant is under pressure from the radiator cap seal. As coolant heats up from hot engine, it expands, and pressure forces the radiator cap seal up, coolant is forced into the reservoir-remember the hot mark on the reservoir? When car is shut off, coolant contracts, creating a vacuum in top of radiator. This vacuum works to suction coolant back from reservoir into the radiator, keeping the radiator topped up, and coolant should now be at the lower cold mark on the reservoir. It is a closed, sealed system. The only loss of coolant will be a very small amount of evaporation from the reservoir. If coolant level keeps dropping, there is a leak somewhere.

Nov 22, 2013 | 2000 Jeep Grand Cherokee

1 Answer

2001 blackbird only running on 2 cilinders: My hbb


stuck float chambers in carbs ...remove service and clean

Aug 01, 2013 | 2001 Honda CBR 1100 XX Super blackbird

1 Answer

Honda blackbird 2002 not starting , it is cut off somewhere


check the fuse at the fuse box, 2nd check the spark plug might be wet @arcing clearnce, if it has kick starter you may try to ground the detached terminal cap of spark plug if it arc as you kick the starter, good, if not fuse busted no supply to the cdi(regulator)

May 22, 2012 | 2002 Honda CBR 1100 XX Super blackbird

1 Answer

How do i remove engine coolant cap on 2001 cadillac dhs


WAIT UNTIL YOUR ENGINE IS COLD,YOUR RADIATOR PRESSURE CAP IS LOCATED ON THE COOLANT OVER FLOW RESERVOIR, THATS WHERE YOU ADD COOLANT WHEN COOLANT LOW,YOU POUR COOLANT IN THE OVER FLOW RESERVOIR UNTIL COOLANT LEVEL REMAIN AT FULL COLD MARK DONT OVER FILL OVER FLOW RESERVOIR, WHEN COOLANT LEVEL STOP DROPPING WHEN ADDING COOLANT AND COOLANT LEVEL STAY AT COLD MARK ON THE RESERVOIR YOU RADIATOR HAS THE CORRECT COOLANT LEVEL IF COOLANT LEVEL KEEP DROPPING CHECK FOR COOLANT LEAKS AROUND RADIATOR AND THE TOP AND BOTTOM RADIATOR HOSES, LOOK FOR COOLANT LEAK AT WATER PUMP GASKET OR SEAL OR LEAK AT WATER PUMP WEEP HOLE IF YES REPLACE WATER PUMP.

Oct 23, 2011 | 2001 Cadillac DeVille

1 Answer

Need to change coolant recovery tank can a anyone do it


Yes you can do it yourself

Degas Bottle Removal
  1. Drain radiator (8005) until engine coolant is out of degas bottle. Disconnect radiator overflow hose (8075) and engine coolant vent hose at degas bottle.
  1. Remove power steering oil reservoir retaining screws and position power steering oil reservoir (3A697) out of the way.
  1. Remove degas bottle return hose and clamp. Remove degas bottle retainers and remove degas bottle.
Installation
  1. Position degas bottle in vehicle and install retaining screw and nut. Tighten retaining bolt and nut to 9-12 Nm (80-106 lb-in).
  1. Connect degas bottle hose and clamp to degas bottle.
  1. Position power steering oil reservoir onto degas bottle and install retaining screws securely.
  1. Connect radiator overflow hose and engine coolant vent hose to degas bottle.
  1. Fill and bleed engine cooling system as described. Check for coolant leaks and proper engine coolant level after engine reaches normal operating temperature.


    q3699b.gif


    Item Part Number Description 1 8100 Radiator Cap 2 - Nut (1 Req'd) 3 - Bolt and Retainer (1 Req'd) 4 - Nut (1 Req'd) 5 - Bolt (1 Req'd) 6 - Coolant Recovery Hose 7 - Coolant Return Hose 8 - Coolant Recovery Hose 9 8A808 Degas Bottle A - Tighten to 9-12 Nm (80-106 Lb-In)
Hope this helps.

Zeppelinx12

Mar 08, 2011 | 1999 Ford Taurus

2 Answers

Where is the engine coolant sensor in a v70 99 volvo


Coolant Temperature Sensor/Switch (For Computer): Service and Repair
ENGINE TEMPERATURE SENSOR
Removal

c32b253.jpg


Engine temperature sensor, 5-cylinder
Jack up the car.
Remove protection cover from under engine.
Drain the coolant.
Lower the car.
Release coolant hose from thermostat housing using pliers.
Remove thermostat housing.
Remove sensor.


02daadd.jpg

Engine temperature sensor, 6-cylinder
Jack up the car.
Remove protection cover from under engine.
Drain the coolant.
Lower the car.
Loosen oil reservoir for servo pump.
Remove coolant reservoir and put it to one side.
Remove screws and outer/upper timing-gear casing.
Remove screws and wire channel.
Disconnect connector.
Remove 4 screws and thermostat housing.
Remove sensor and wires.
Installation
Engine temperature sensor, 6-cylinder
Install thermostat housing sensor.
Position wires in slot on thermostat housing.
Note! The white marks should be positioned in lower opening of slot, from underneath.
Position gasket on thermostat housing correctly and install thermostat housing using two of the screws.
Position thermostat housing correctly and tighten the four screws.
Position wire channel correctly and position wire in channel.
Tighten screw on wire channel.
Connect the connector.
Install outer/upper timing-gear casing.
Install coolant reservoir.
Install oil reservoir for servo pump.
Follow-on work, 6-cylinder
Fill up coolant.
Warm the engine until the thermostat opens.
Switch engine oft and check the level. Re-fill if necessary.
Check for leaks.
Check in VADIS vehicle communication (read-out of parameter values), for current engine system, that the engine temperature shown appears
correct.
Engine temperature sensor, 5-cylinder
Install in reverse order.
Follow-on work, 5-cylinder
Fill up coolant.
Warm the engine until the thermostat opens.
Switch engine off and check the level. Re-fill if necessary.
Check for leaks.
Check in VADIS vehicle communication (read-out of parameter values), for current engine system, that the engine temperature shown appears
correct.

Sep 19, 2009 | 1999 Volvo V70

1 Answer

Replace a coolant reservior on a 1999 ford taurus


If you need Illistration I Can Email it to you Im at
rejakwilson @ aol.com

Removal

CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs, the service change interval on Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.

  1. Drain radiator until engine coolant is out of degas bottle. Disconnect radiator overflow hose and engine coolant vent hose at degas bottle.
  2. Remove power steering oil reservoir retaining screws and position power steering oil reservoir out of the way.
  3. Remove degas bottle return hose and clamp. Remove degas bottle retainers and remove degas bottle.
Installation
  1. Position degas bottle in vehicle and install retaining screw and nut. Tighten retaining bolt and nut to 9-12 Nm (80-106 inch lbs.)
  2. Connect degas bottle hose and clamp to degas bottle.
  3. Position power steering oil reservoir onto degas bottle and install retaining screws securely.
  4. Connect radiator overflow hose and engine coolant vent hose to degas bottle.

Aug 28, 2009 | 1999 Ford Taurus

Not finding what you are looking for?

Open Questions:

0 Answers

hi, i have a problem with my cbr 1100 xx 98model with a rough running,spluttering in just highway speeds when im crusing,it starts easy warm or cold and runs fine on idle and runs nice up to 60 kmh and runs fine after 6or7000 rpm and up to rev limiter but difficoult crusing 60 up to relative high speeds in high gears. runs fine in low gears in town. the fuelconsumtion seams to be some high at crusing speed that indicates that is rich mixture but it runs better at crusing speed if i pull the chocke a little that indicates lean mixture, i know this sound stupid but this is true so i was thinking the fuel is not properly mix with the air, more like drops than mix with air maybe? sparkplugs looks nice light brown. carbs and petcock have be cleaned many times, new sparkplugs, the ht leads looks good. it changes the speed it splutter at to higher speed if i shim the needles higher but if they too high i can almost not take off bcoz too much fuel at small trottleopening and black smoke from the exaust, my bike dnt have needles with groves for a clip thats why i shim them instead. a bikemechanic friend he told he have some simelar problem on a yamaha tdm 850 before and first when he change the nozzle in the carb that the needle goes in to it was cured, the nozzles was oval worn he told and its a problem on downdraft carbs he thinks, but on the xx carbs the nozzle is not specified as sparepart and its pressed in to the carbbody, my nozzle looks a little bit oval on atleast 2 of the carbs if looking closely or maybe only imagination in my eyes, im not sure. do someone had problem with the nozzles in the carbs before? i have cleaned the carbs and petcock many times, the airfilter is some dirthy but its worse without filter so its for sure not bcoz of the filter, the bike have a twobros 4in1 exaust and i have try 140,145 and 150 mainjets,but the problem is not with mainjet circut i think for sure. i had be very happy if someone could have a solution for this bcoz the bike is only irritating to use now and have be more or less the same all the time since i bought it. hope someone can help get my bird flying as it should do! thanks in advance!

Mar 12, 2011 | 1998 Honda CBR 1100 XX Super blackbird

See all 1998 Honda CBR 1100 XX Super blackbird Questions

1998 Honda CBR 1100 XX Super blackbird Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...