Question about 2009 Harley Davidson FLHX Street Glide
Posted by Anonymous on
Hi Anonymous, when checking for spark the CKP needs to measure the compression bump in order to send the correct signal to the ICM/ECM so always check for spark with either a third plug grounded or lift the end of the plug boot 1/2 " off one of spark plugs that are in the head. and the usual suspects are:
1. Fuel tank empty
2. Fuel supply valve turned off.
3. Fouled spark plugs.
4. Engine flooded with gasoline as a result of over use of enrichner.
5. Fuel valve or filter clogged.
6. Vacuum hose to automatic fuel supply valve disconnected, leaking, or pinched.
7. Discharged battery, loose or broken battery connections.
8. Loose wire connection at coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, spark plug cable connections loose,
or cables connected to wrong cylinders.
10. Ignition timing incorrect due to faulty ignition coil, ignition module, or sensors " Manifold Absolute Pressure" "Camshaft Position Sensor" "Crank Position Sensor" "Brake Apply Sensor
11. Engine lubricant to heavy ( winter operation )
12. Sticking or damaged valves or push rod wrong length.
13. Primary cam sproket spline sheared or missing spacer.
14. Security alarm system not disarming.
For a primary suspect please visit the website below: Good luck
Harley Diagnostic Codes 04 to Present
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...
Posted on Jun 07, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1 remove the screw on the bottom of the chrome ring 2 remove the three screws from the retaining ring 3 pull headlight out and unplug.To remove the bulb remove rubber boot and push down on wire loop and push end out from under the retainer lip (you can loosen the screw 1/2 to1 turn if needed) remove bulb and replace. The new one turnso that the wider ear is pointing up (use the emblem on front)
Posted on Mar 21, 2010
SOURCE: bike won't start, new Harley
I'm not too familiar with the later model bikes but if I were getting a clicking noise under the seat and the bike was not starting, I'd investigate the source of the noise. It's possible that it is a starter relay that engages the solenoid that is an integral part of the starter. Look at the starter from the right hand side of your bike. You'll see a single small wire that connects to the end of the starter just above the end plate of the solenoid. Disconnect this wire and connect a test light or volt meter to the wire. Turn on your ignition switch and press the start button. You should hear the click under the seat and see voltage at the end of that wire. If not, replace the relay, a plastic cube about an inch in dimension.
Posted on Jul 02, 2011
Tips for a great answer:
Jul 17, 2013 | 2007 Harley Davidson FLHX Street Glide
Feb 12, 2013 | 2009 Harley Davidson FLHX Street Glide
Sep 21, 2012 | Cars & Trucks
Sep 12, 2012 | 2009 Harley Davidson FLHX Street Glide
Jul 11, 2012 | 2009 Harley Davidson FLHR Road King
Apr 01, 2012 | 2009 Harley Davidson FLHX Street Glide
Oct 09, 2011 | 2009 Harley Davidson FLHX Street Glide
Apr 22, 2011 | Harley Davidson FLHX Street Glide...
Nov 19, 2009 | 2008 Harley Davidson FLHX Street Glide
82 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: