Question about Motorcycles

Open Question

Need a wiring routing diagram for a 2000 yamaha big bear 400 atv

Cant find the electric fan relays

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: yamaha big bear no spark

I'm not familiar with all quads and all the kill switch locations. Does it have a tip-over kill switch? Is it working? Is the quad in neutral? Is the neutral light on? Many engines will not spark if the neutral light is not on. Are the headlights off when starting?

How good is your battery? A low battery can kill spark. Test for spark by grounding the threads of the plug against the cylinder. Have a friend kick the bike while you watch for spark. Assuming no spark, then check all the kill switches with an Ohmmeter to be sure each switch is working properly. Sometimes a switch goes bad. Try disconnecting all kill switches then check spark.

Check the wiring harness, even under the gas tank and seat. Are all the connectors clean and with a tight connection? Any abraded wires? Check the ignition switch also. The switch can go bad as well. Are the flywheel coils good > is the battery getting a charge?

Still no spark? If CDI then get it checked.
If points then file or replace them along with a new condensor and reset the gap then time the engine. >> I hope this helps.

Please rate this answer. Thanks trsrhntr!

Posted on Apr 03, 2009

co7196
  • 3433 Answers

SOURCE: no front brakes on 95 yamaha big bear atv

gravity bleed. make sure fluid is always full. crack open the bleeder screw and let the brake fluid drip until no bubbles. Then close bleeder top off fluid and replace cap. Now, pull the brake handle. If there is no pressure or has bleed down, the master cylinder is kaput.

Posted on Jun 20, 2009

  • 10865 Answers

SOURCE: need wireing diagram for 1981 yamaha 400 special

get the clymer yamaha motorcycle repair manual for 1981-2002. it will be twenty bucks well spent.

most book stores carry it or you can go to a motorcyle shop or on the internet at clymer.com

Posted on Jun 26, 2009

  • 19 Answers

SOURCE: yamaha big bear 400 will

Sounds like a problem with the starter, could be a starter fuse, relay or solenoid. The start cicuit wiring could also be damaged. If you can pull-start the motor, and it runs fine, you have pretty much eliminated any problems with the motor. Check the wires running from the start button make sure they are intact, also trace them and look for around a 1" cubed black box. This is the relay, when you push the button, if its working, you will feel the box click. Also locate the starter and do the same thing. If you feel or hear the starter click, the solenoid is working. The battery voltage could also be too low to energize the starter motor. Could also be a battery or alternator issue. Check the battery voltage and for any sounds coming from the bike when you push the start button.

Posted on Aug 21, 2009

FitzOriginal
  • 842 Answers

SOURCE: need wiring diagram for electric

Based on the original Honda spec, you can see a diagram here:
http://www.buyatvsonline.com/chinese-atv-110-wiring-diagram-p-10430.html

Posted on Feb 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Complete wiring diagram needed


Hi ! for a free wiring diagram, please visit the website below. If you need more information about a specific electrical issue you can reach me at motor@motorpartstore.com.
http://www.motorpartstore.com good luck and have a nice day.

Apr 14, 2016 | Yamaha 2004 Big Bear 400 4x4

1 Answer

2005 Yamaha Big Bear 400. How do I replace rear brakes?


Removing The Rear Brake Drum & Shoes on Grizzly 600 ...

? 5:04
www.youtube.com/watch?v=n5oO7v3nT6s
Mar 11, 2012 - Uploaded by myquadrepair
Removing the rear brake drum & shoes on Yamaha grizzly 600. ... Yamaha Big Bear Oil Change and More! - Duration: 10:43. by jfrost77hd ...

HONDA FOREMAN REAR BRAKE CHANGE PART 1 ...

? 11:49
https://www.youtube.com/watch?v=xQanZdlDCI0
Jul 17, 2012 - Uploaded by 400EX99N
HOW TO CHANGE REAR BRAKES ON A HONDA ATV. ... is this about the same for a 2004 yamaha big bear 400? Read more Show less.

Nov 03, 2015 | ATVs

2 Answers

I have a Yamaha 400 big bear and cooling fan won't


Start by checking the fuses... If they're fine the start tracing the wiring from the fan. Look for any burn marks, pinches, etc... If in doubt I'd recommend taking it to a professional. It's really easy to mess things up if your not sure what your doing

Mar 20, 2013 | Motorcycles

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...