Question about Peugeot Motorcycles

1 Answer

Moped wont pull away

It revs on the stand but when sitting on it will not pull away and revs wont pick up any ideas please

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 157 Answers

If it is a two stroke engine( has an oil injection tank or requires oil/gas premix) it could be a carbon clogged exhuast port and or pipe. Try removing the exhuast pipe and viewing the inside of the exhuast port. Scratch out all crusty carbon buildup. I have seen ports virtually close themselves off with carbon in extreme cases. After cleaning try running with exhuast removed. It will be very loud but will tell you if pipe is clogged. If it is the best way to fix is to replace the muffler. Good luck.

Posted on Jan 05, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

landsend
  • 1066 Answers

SOURCE: honda x8rx will not pull away

your cars needs cleaning and you need a new spark plug.

Posted on Mar 26, 2009

ollie reece
  • 1167 Answers

SOURCE: carb tune up gilera runner 50

on the carb you will find 2 screw one will be quite far in than the over thats the one you adjust this is the mixture screw which controlles the air and petrol together unscrew it say 1/4 a turns at a time and see if it improves if it gets worse screw it the oposite way and see if that improves good luck buddy

Posted on Aug 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yamaha xj600


strip and clean carbs and if fuel older than 6mths replace it !

Aug 11, 2014 | Motorcycles

1 Answer

Hi i have a julin fighter scooter 50cc this morning the drive belt broke replaced the drive belt got the bike to start and it revs high when on the stand but when we kick it off the stand it will only tick...


Hi, Anonymous and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
Good luck and have a wonderful day.

Jul 03, 2017 | Motorcycles

1 Answer

Peugeot vivacity 50 wont start no spark from plug


these little mopeds can be irksome at times ,it will not start if the side stand is down even pulling the brake levers in it will not start like this only if the side stand is up ,so put it on the main stand and try again

Apr 05, 2012 | Cars & Trucks

1 Answer

I have a keeway speed 125 and the engine sut out on me the other day , it will start and sit at idle but wont rev , it just cuts the engine . any ideas?


try the needle on the end of throttle where i goes into carb, mine was wor and very loose moved needle to a higher notch and away it went. but really needs new needle

Jun 03, 2011 | 2010 Keeway Speed 125

1 Answer

I have a 1992 F150 4.9L. couple weeks ago it stalled out and wouldnt start, changed the coil it started right up and abot four more times that day then nothin. I have a new coil, new ecc, new cap,rotor,...


1) Have a look at the starter relay. Pull it out and ease the cover off and then check out the state of the solder joints. If any are dry and or there are signs of annular cracking around any of the power pins simply reheat with soldering iron to make good. 2) Check out your idle air control valve. Clean the throttle body interior and passageways to and from the IAC. Check that the valve is free to open and that it opens when at idle. 3) Check out your fuel pressure regulator (FPR). It sits on the end of your fuel rail. When the car is idling pull the vacuum line from it. The engine revs should pick up for a few seconds before running roughly. If you do not get this response apply vacuum to the FPR and this should cause the engine revs to drop. If by applying suction you pull fuel throught he vacuum port then the FPR needs changing 4) Lastly check all vacuum lines. Spray suspect areas with WD40 and if there is a leak there the engine will jump slightly in revs.

Oct 13, 2010 | 1992 Ford F150 SuperCab

2 Answers

2003 VW Golf 1.9 GTI Turbo Diesel


Hi,if you want to make sure its your airflow meter,get a buddy with the same car and just test his in your car..(A.F.M is situated on the left,behind your battery is the filter box,the pipe connecting to the box is where it sits)

Mar 01, 2010 | 2003 Volkswagen GTI

1 Answer

Honda x8rx will not pull away


your cars needs cleaning and you need a new spark plug.

Mar 26, 2009 | 2003 Honda XR 400R

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Joseph Hoffmann

Level 3 Expert

1702 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Vernon Taylor

Level 3 Expert

2909 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...