Question about Motorcycles

Open Question

Locating oil drain plug on kawasaki 3010 mule 2002 617cc

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2712 Answers

SOURCE: oil drain plug

Follow the hose that goes to the frame from the oil tank. Loosen the clamp and pull.

Posted on Nov 20, 2008

rylee_smith
  • 8619 Answers

SOURCE: oil drain plug

Hi
It is located on the right side just under the oil tank ; if you follow the rudder hose that exits the rear right side of your oil tank it leads to the bottom of the frame under this is the oil plug. This hose has a plug clamped to the end of it or stuck into a prug that is welded to the frame.
After this unclamp and pull the plug to make sure that you have the dipstick out before pulling it loose.

Please do rate the solution as "FixYa" if found useful and revert for further assistance.
Thanks Rylee

Posted on Mar 27, 2009

  • 25 Answers

SOURCE: Kawasaki Mule 3010, keeps getting flat battery, wont jump start

Sometimes when the battery keeps going dead like that, a component may be creating a current draw. you can do a simple current draw test with a fluke meter by setting the meter to read amps, make sure the test leads are in the proper portals on the fluke for an amp test, and disconnect one of the battery cables and connect the test leads in-line with the battery and cable. It would help to know you have a good fuse inside the fluke. They are easy to blow, and whatever you do, DO NOT try to start the unit with the meter hooked up for the amp draw test. That is how fuses are blown. With the key off, check for any amp draw. If there is, you can start unplugging components until the draw goes away. If there was no draw to begin with, you may have a stator coil (or alternantor, whichever it has) that is weak and can't keep up.

Posted on Jun 11, 2009

  • 280 Answers

SOURCE: oil drain plug for 2006 flhrs

The nut is a 5/8 socket, its almost directly under the seat on the bottom of the engine. Best to pull out the dipstick to drain the oil quicker. Use a new washer when you refit the sump plug to prevent leaks.

Posted on Jan 26, 2010

bonedivers
  • 1140 Answers

SOURCE: what type of oil is

Synthetic is best but also $$$$$$. Just buy your oil from dealer, mine holds a hair under 4 qts (i use 4 qts) with filter. drain plug is under motor assy (bottom)

Posted on Jun 04, 2011

Testimonial: "thank you for the quick response. I went and bought 4 qts. I put in just over 3 1/2 w/new filter. when the bike is straight up it covers the line."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mule 3010 has no power. in low or high it goes maybe 9 mph, has new pump, spark plugs, checked the vents, nothing is helping


What is the compression? This leads me to think you may have more of an internal issue.

Have the compression checked, with throttle wide open, then repost with the results.

May 20, 2017 | kawasaki 2005 Mule 3010 4x4

1 Answer

I have a 2003 kawasaki mule model 3000 it wont say running at idle what to do


Full tune up and carb clean .get new plug,air filter.oil Chang ,carb clean and adjustment.that should do it.,., try fuel filters and test fuel pump see if it's functioning properly.,.

Dec 10, 2016 | kawasaki 2005 Mule 3010 4x4

1 Answer

Where is the neutral safety switch for a kawaski 3010 mule


Kawasaki Mule Update - YouTube

? 2:16
www.youtube.com/watch?v=Fw_jeQUU6Hw
Jan 25, 2013 - Uploaded by Penguinboy1995
solenoid is reading battery voltage and the constant hot, it is not sending the 12 volts from the switch to the ...

Sep 19, 2015 | kawasaki 2005 Mule 3010 Trans 4x4

1 Answer

What does Kawasaki mule 3010 do when belt breaks


makes all kinds of noise in houseing and if belt is not full broken will still go fwd

Sep 23, 2014 | kawasaki 2008 Mule 3010 Trans 4x4

1 Answer

What is possible cause that a mule 3010 kaf620e6f will not hold idle?


Air leak .dirty air filter.,.fouled plug.,.bad gas.,.dirty carb?fuel injection? Bad fuel filter ,fuel pump test fuel pump that's the general stuff.go from there

Apr 28, 2014 | kawasaki 2006 Mule 3010 4x4

2 Answers

#1cylinder not firing on 2003 3010 Kawasaki mule


if its firing ok on other cylinders, unlikely to be pump or fuel filter, focus on electrics, plug, ht lead etc

Dec 08, 2013 | 2003-2007 Kawasaki Kaf620 Mule 3010 4x4...

1 Answer

Kawasaki mule 3010 won't do right and left signals when i press them, how to switch fuse for them?


Identify the fuse responsable for turn signals, extract it and insert another one with the same value in it's place.
Also could be turn's signals relay fault.

Oct 20, 2013 | kawasaki 2008 Mule 3010 4x4 Diesel

1 Answer

Kawasaki mule 3010


Check the starter or solenoid.

Apr 27, 2013 | kawasaki 2008 Mule 3010 Trans 4x4

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...