Question about Yamaha Motorcycles
Hi Blossercj, you could have a faulty spark plug, spark plug cable, or ignition coil, Good luck and have a nice day.
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Sep 27, 2015
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
check stator ac output 1st.check pulse coil next. find cdi box to try next.other possibles- ign coil, try unscrewing plug cap & trimming about 1/4" off coil wire. check spark w/ cap off. finally could be wiring.
Posted on Feb 16, 2009
Your gas is bad. I have to change my all the time If your starter turns but dose not engage the starter barring is out DO NOT BUY STOCK. buy after market when you replace that. they
Posted on Mar 21, 2009
Here are a few things to do >>
How old is the gas in the gas tank? Get fresh fuel.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Clean the bowl and filter screen if present, then re-mount them, ( not all bikes have a water trap bowl or screen ).
Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.
Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. Set the idle speed with the idle screw.
I am uncertain if the bike has ran for you or not. "Did pull the spark plug and kick started it." If the bike still will not run then the cam chain may be out of time. Why was the tensioner off the bike?
Please rate this solution. Thanks budx5!
Posted on Apr 04, 2009
Drain and replace the gas with fresh.
Remove the air cleaner and spray carb cleaner into the inlet. Work your throttle a little then put everything back together and try to start it.
Posted on Jun 02, 2009
Tips for a great answer:
Aug 05, 2014 | MSR 2003-2009 Yamaha Wr450f Dirt Bike...
May 04, 2013 | 2005 Yamaha TTR 90 E
Mar 18, 2013 | Yamaha YZ 125 Motorcycles
Feb 22, 2013 | 2006 Yamaha DT 125 RE
Jan 04, 2013 | Yamaha XPeed 50 R Motorcycles
Sep 07, 2012 | 2004 Yamaha YZ 125
May 03, 2012 | 2002 Yamaha YZ 426 F
Sep 29, 2010 | 2003 Yamaha WR 250 F
Apr 06, 2010 | 2000 Yamaha TT 600 R
Apr 24, 2009 | 2002 Yamaha TT-R 125
68 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: