Question about Honda Motorcycles

Open Question

Master cylinder sight glass replacement

Vf 750 C

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bennito10
  • 51 Answers

SOURCE: hoda vf 750 wont start

hello and welcome
with that long of a storage period it is a safe bet that the jets in the carbs have plugged over. this can happen with little as a month or two without proper winterization or fuel conditioning prior to storage. so the carbs will need to be removed and cleaned properly. this is quite the task on the older v4 hondas. and i would reccomend a manual before doing so. after being removed a good can or two of aresol carb cleaner and a small gauge wire to break up builup can clean these carbs out. this is a very very common problem. and im sure you will find this to be the source for your no start. thank you.

Posted on Mar 22, 2009

sisadsl
  • 1508 Answers

SOURCE: I have a 1977 xs 750 and I have to replace the

The 79 one should work fine

Posted on Jun 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I tried to vacuum bleed the clutch slave cylinder on my 1982 Honda VF 750s. I was unable to do so. I removed the cylinder, filled it with brake fluid, reinstalled it, and tried again. Still nothing!...


Usually if you just loosen the banjo bolt and pump the lever a couple of times till a gush of DOT 3/4 brake fluid starts to leak past the threads. Now you should be able to tighten the banjo bolt and bleed out the system. Lay some plastic and rags under the master cylinder so you do not damage the paint or plastic with DOT 3/4 brake fluid.

Jul 08, 2011 | 1982 Honda VF 750 S

1 Answer

How do you fix an over traveled clutch piston when it goes into the mater cylinder


honda does make a rebuild kit for the hydraulic cluch master cylinder

Mar 27, 2010 | 1987 Honda VF 750 C Super magna

1 Answer

Front brakes too soft.Thank you.


either you have air bubbles in the front brake lines or calipers and will need bleeding out, if this doesnt work youll have a faulty front master cylinder replace it and bleed the system again

Nov 17, 2009 | 1982 Honda VF 750 S

1 Answer

Problems with timing the camshafts for a VF 750 Interceptor . It is the two front cylinders problem. The engine works, but not good. When running it is blowing out back of the two carburators.. i have a...


The cam timing is pretty straight forward: with the #1 cylinder at top dead center, the timing marks on the cam sprockets should be level with the valve cover gasket surface.
I can't imagine the engine would run at all if the cam timing were off, my suspicion is that the intake valves on the two forward cylinders are bent (explaining the blow-back through the carburetors). This can occur if the crankshaft is rotated without first having the cam timing set correctly.

Nov 17, 2009 | 1984 Honda VF 750 S

1 Answer

Rebuilding slave cyclender on 1985 honda vf 700 need diagram on how to rebuild clutch slave cylinder


Please visit this site and you will get the general idea on the clutch slave cylinders.
http://www.fjparts.com/clutch_slave_cylinder_diagram.htm

This site for parts:-http://www.bikebandit.com/houseofmotorcycles/honda-motorcycle-vf700c-magna-1985/o/m2752

Hope this helps!

Sep 14, 2009 | 1984 Honda VF 750 S

1 Answer

Vacume tuning 1983 vf 750 honda


I give this site a go, I found great info on repairs of my Sabre.

http://www.sabmag.org/

I hope this may help,
Tom

Sep 05, 2009 | 1984 Honda VF 750 S

1 Answer

I have a 82 v45 magna that has the same problem with the clutch aswell,it has no pressure we tried to bleed it and did it the correct way but now i have nothing in the clutch?


Either has a bad clutch master cylinder, or a bad slave cylinder. If you can line lock the clutch, does it have good pressure? If not, you need a clutch master, if so, it is slave cylinder, or a bad clutch.

Aug 03, 2009 | 1982 Honda VF 750 S

1 Answer

No pressure in a motorcycle clutch


bleed the master cylinder first,fill the resovoir pump the lever a few times and crack the bolt that holds the line to the mastercylinder,do this two or three times or untill all the air is gone from the master cylinder piston assembly,you should then be able to bleed the rest of the line,dont let the fluid get to low when bleeding the line out as you will end up with an air lock in the piston assembly again

Jun 25, 2009 | 1982 Honda VF 750 S

1 Answer

Clutch


Check to make sure the slave and master cylinders are working. You can probably bleed it if the slave cylinder started leaking. Could possibly be internal on the clutch master.

Mar 06, 2009 | 1988 Honda VF 750 C Super magna

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...