Question about 1993 Suzuki VS 800 Intruder

1 Answer

Installing front tire on 1993 suzuki intruder vs800gl. Need torque specs for front axle bolt and brake caliper mounting bolts.

Posted by on

  • boothusmc Jan 17, 2009

    Thanks, but I found the actual specs. It's 26 to 37.5 ft-lbs.

  • Anonymous Mar 15, 2014

    need a step by step installation for 1973 sportster motor need to know bolt and spacer placement. purchased front and rear motor mount bolts and spacer kit but dont know the placement. need a good picture my manual dont show much

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 74 Answers

A good rule of thumb is 14 foot lbs.

Posted on Jan 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NNeed torque specs for 2010 harley ultara classic, front axle nut, front brake calipers, axle nut holder


Front Axle = 60 to 65 foot pounds

Front caliper banjo bolts = 17 to 19 foot pounds

Front Brake disk screws = 16 to 29 foot pounds

Front caliper mounting bolts = 28 to 38 foot pounds

Front axle holder nuts = 132 to 180 inch pounds

Aug 23, 2014 | 2010 Harley Davidson FLHTCUTG Tri Glide...

1 Answer

What are the torque specs for 2010 harley ultra classic, front axle nut, front brake calipers


Front caliper -

Brake Pad Pin = 75-102 INCH lbs.

Caliper to Fork Bolts = 28-38 FOOT lbs.

Aug 23, 2014 | 2010 Harley Davidson FLHTCUTG Tri Glide...

1 Answer

No problem I need torque spec's front brake rotor,front axle nut and front brake caliper bolts 2005 Harley davidson ultra classic


caliper torque 28-38 ft lbs,front axle nut torque60-65 ft lbs. front brake rotor torque 16-24 ft lbs. straight from harley manuel.

Aug 14, 2011 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

CYL HEAD BOLT TORQUE SPEC AND CAM HOLDER BOLT SPECS.


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs
TF

Apr 28, 2011 | 2008 KTM 450 SX-F

1 Answer

I have just purchased a Kawasaki 98 GPXR motorbike and need to replace the front wheel tyre. How do i go about removing the wheel so that i can take it to the mechanics to get this done?


Torque specs:

Front axle = 80 ft/lb
Front axle clamp bolt = 15 ft/lb
Front axle caliper mounting bolts = 25 ft/lb

Front Wheel Removal:

1. While the bike is still on the rear stand (but before putting it on the front stand), loosen the front axle clamp bolt with a 6mm hex bit. You do not need to remove it fully, just be sure it's loose.

2. Using the 14mm hex bit, loosen the front axle bolt. A breaker bar makes this step easier. Once it is loose you can go ahead and place the motorcycle on the front stand.

3. Using the 12mm socket, remove the front brake caliper mounting bolts. Once you have the brake off of the rotor, replace the bolts back in the caliper to prevent losing them. Hang the brake using cable ties or twine. BE SURE NOT TO PUSH THE BRAKE PEDAL! This will compress the brake pads and make it difficult to re-install. Repeat the process for the other side.

4. Once the brakes are tied off out of the way, finish removing the front axle bolt. It's helpful to use some wood to support the wheel while removing the axle bolt. Be sure to note the spacers on the wheel between the forks and the wheel. Remove them so they don't get lost. These will need to be greased before reinstalling.

5. Installation is the reverse of removal. Be sure to replace the calipers and torque them to 25 ft/lb. Once the front axle bolt has been torqued to 80 ft/lb, be sure to drop the front to the ground and bounce the front forks 4-5 times. This will seat the forks on the axle. Then you can tighten the front axle clamp bolt to 15 ft/lb.

Mar 26, 2011 | kawasaki GPX 750 R Motorcycles

1 Answer

09 KTM 250xc-f I am rebuilding the motor and I need the torque specs for this bike can you please help.


Thanks for contacting FixYa. I was reviewing some of the older un-answered questions trying to ensure your issue has been resolved.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

TF

Sep 28, 2010 | KTM 250 XC Motorcycles

1 Answer

Head torque specs.on 1991 KTM540 2-stroke


Thanks for contacting FixYa. I was reviewing some of the older un-answered questions trying to ensure your issue has been resolved.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

TF

Sep 03, 2010 | KTM MXC 520 Racing Motorcycles

1 Answer

Need torque specs for front wheel cross pin and nut and bolt in fork on 2005 1200 custom


Front axle nut = 50-50 ft. lbs.
Front axle pinch bolt and nut = 21-27 ft. lbs.
Front brake caliper mounting bolts = 25-30 ft. lbs.
Handlebar clamp bolts = 12-15 ft. lbs.
Front Fork
Upper bracket pinch bolts = 30-35 ft. lbs.
Lower bracket pinch bolts = 30-35 ft. lbs.
Fork stem pinch bolt = 30-35 ft. lbs.
Front fender fasteners = 9-13 ft. lbs.

Mar 03, 2010 | 2005 Harley Davidson XL 1200 C Sportster...

1 Answer

I need the torque settings for changing the wheels on my BMW HP2 as I have lost the settings for the front axle,front brake caliper and rear wheel bolts


BMW workshop DVD says Front axle M22x1,5 (greased) = 50NM Front axle pinch bolts = 8NM Brake caliper to fork bolts = 30NM Rear wheel bolts M10x53x1,25 = 60NM
Brake caliper to fork torque needed if changing to SM wheels. Method. Torque greased axle bolt to 50NM, then compress forks several times without using brakes, then tighten both LHS axle pinch bolts to 8NM, then tighten both RHS axle pinch bolts to 8NM. Then test your brakes are working. Front finished. Rear. Torque to 60NM. I torque every second bolt as I work my way around the 5 Torx screws until they have all been torqued and double checked

Jul 22, 2009 | 2006 BMW HP2 Enduro

Not finding what you are looking for?
1993 Suzuki VS 800 Intruder Logo

351 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4471 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...