Question about Motorcycles

1 Answer

No fuel to carbretta - Motorcycles

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 462 Answers

Unhook hose from fuel tank to see if fuel is present if yes follow hose to next point be it filter or carb if no filt between then undo hose at carb verify fuel if none there hos is bad if fuel undo cover on carb should be screen inside or filter need cleaned or replaced

Posted on Dec 12, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace fuel pump on 2005 chevy monte carlo


The pump is in the gas tank, so the tank has to come out.

Apr 28, 2016 | Cars & Trucks

1 Answer

Jonway


Clean the plug.
Close the gap a little to get a stronger spark (temporary)
Use starting fluid to aid starting (a little will do it)

Jan 13, 2014 | Motorcycles

1 Answer

Whilst riding my lambretta li 125 special fiited with an af175 cc kit and jettex carbretta at 40-45 mph it cut out there was no noise,no spoke ,no oil spealage no clanking but when i stopped and tryed to...


Hi, a two stroke engine relyes on 3 things to run, spark, fuel, compression, without 1 of the above the engine will not run, you say there was no smoke, this concerns me a two sroke engine makes smoke as it burns the oil used to lubricate the engine, was the bike down on power before it cut out? My thoughts are some damage has occured inside the cylinder, as a result your compression has been reduced, thus fuel canot be ignited as it passes the piston, instead of remaining inside the combustion chamber where the spark takes place, you should also check the condition of both the base and cylinder head gasket, remove cylinder head and check for contact marks where the piston may have made contact with it, contact of this part will cause damage to the piston, causing the rings to become seized into the piston thus reducing compesion

Apr 23, 2011 | Aermacchi Sprint 350 Motorcycles

1 Answer

My gt750 seems to be starving/sluggish under acceleration


im guessing that its an early model with carbs these may need a good clean you may have water or dirt in your fuel the air filter may need replacing and the spark plugs and leads. from memory its a bit of a mission removing the carbs as i remember it is easier if the air box is removed first keep all parts seperate when striping the carbs if your not confident do them one at a time so you can use the next one as a reference if you get confused as to where the parts go use carbretta cleaner and compressed air to clean with dont use wire to clean the holes in the jets. clean the outside first before you remove the float bowls and use a good screwdriver the philips head screws have a tendancy to be difficult and and its not hard to chew the centre out of the screw if this happens use a centre punch and hammer punch the head of the screw to loosen it an impact driver should undoo tight screws that are not damaged

Apr 06, 2011 | Suzuki GT 380 Motorcycles

1 Answer

Location of and how to remove and replace - 2002 DeVille Sending Unit/Fuel Pump Module (4.6L engine)


These units are in the tank and must be dropped in order to replace.


WARNING Do not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

  1. Relieve the fuel system fuel pressure, as outlined in the Fuel System Section.
  2. Drain the fuel tank to at most 3/4 of a tank full.
  3. Raise the vehicle.
  4. Remove the fuel tank.
    NOTE The modular fuel sender support assembly will spring-up when the locking ring is moved.
  5. Remove the fuel sender assembly using tool J39765 Fuel Sender Locknut Wrench or an equivalent.
  6. Note the position of the fuel sender strainer for installation.
  7. Support the reservoir with one hand and grasp the fuel sender strainer with the other hand.
  8. Pull the external fuel sender strainer off of the fuel sender.
  9. Inspect the fuel sender strainer. If the fuel sender strainer is contaminated, the fuel tank should be cleaned.
  10. Discard the fuel sender strainer after inspection.
  11. Disassemble the electrical connectors from the fuel level sensor assembly of the fuel pump and cover assembly.
  12. Disassemble the fuel level sensor assembly.

    0996b43f802054cc.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Fuel level sending unit on fuel sender (fuel pump) module.


To install:
  1. Assemble the fuel level sensor assembly.
  2. Assemble the electrical connectors to the fuel pump and cover assembly.
  3. Position the new fuel sender strainer on the modular fuel sender and push on the outer edge of the fuel sender strainer until the fuel sender strainer is fully seated on to the sender assembly.
  4. Install the fuel sender assembly into the fuel tank using tool J39765 Fuel Sender Locknut Wrench or an equivalent.
  5. Reinstall the fuel tank.
  6. Lower the vehicle.
  7. Add fuel to the fuel tank.
  8. Connect the negative battery cable.
  9. Reinstall the fuel tank filler pipe cap.
  10. Inspect for fuel leaks.
  11. Turn the ignition switch ON for 2 seconds.
  12. Turn the ignition switch OFF for 5 seconds.
  13. Turn the ignition switch ON .
  14. Check for fuel leaks.

Oct 26, 2010 | 2002 Cadillac Deville

1 Answer

I would like some advice on how to tune a cs 3400 echo chain saw


Hi, you can't tune these, so if its not running smoothly, check air filter, clean and replace. Check spark plug, clean if necessary and replace. If problem persists it could be dirt in the carbretta, so flush this out with clean fuel, after this, drain fuel tank and replace with fresh fuel, ensure you have the correct mix of fuel.
Hope this helps

Aug 19, 2010 | Echo 30.1CC Chainsaw With a 14 In.bar and...

2 Answers

Hi 6000 watt generator sat for 6 months with fuel shutoff. now will only run with choke on. thanks, Glenn


Hi, sounds like derty fuel, you will need to check and clean air and fuel filters; also wash your carbretta out with lean fuel. Drain fuel tank and replace with fresh fuel.

Aug 06, 2010 | Honda Electrical Supplies

1 Answer

Where do I find the fuel pressure regulator and how to change it on a 2001 hyundai xg300


The fuel pressure regulator is built in to the fuel pump

f89c7c1.gif
Fuel tank and fuel pump assembly—XG 300

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Fuel supply, return and vapor lines
    • Fuel fill and vent hoses
    • Fuel pump module connector
    • Fuel level sender connector
    • Fuel tank straps
    • Fuel tank
    • Fuel pump module
To install:
  1. Install or connect the following:
    • Fuel pump module and torque the mounting bolts to 12–24 inch lbs. (1–3 Nm)
    • Fuel tank
    • Fuel tank straps
    • Fuel level sender connector
    • Fuel pump module connector
    • Fuel fill and vent hoses
    • Fuel supply, return and vapor lines
    • Negative battery cable
  2. Fill the tank with fuel and check for proper fuel pump operation.

Jan 10, 2010 | 2001 Hyundai XG300

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...