Question about 2011 kawasaki ZZR 1400

Open Question

Tank removal of zzr 1400 - 2011 kawasaki ZZR 1400

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tabbycat282
  • 56 Answers

SOURCE: ZZR 1400 wiring identification assistance

Try this site look for zzr 1400 wiring diagrahm http://www.mediafire.com/?81yj7rotpej Hope i helped pwalsh.!!.....

Posted on Nov 10, 2009

  • 27 Answers

SOURCE: I have removed all bolts

It's quite common for fairings to be held together with push in rubber grommets and also slots and tabs between fairing pieces. There is also a newer kind of snap connector which looks and works kind of like velcro except that it snaps open and closed, there is no "half way" on these ones, they are either holding together or not.

I'm not familiar with your model or which fairing you are taking off but I have 2 kawasakis myself from similar era. The belly pan panels need to be split (usually connected together with plastic plugs rather than screws), then rotated to free them up so they slide off from the side panels. My tank side panels had a combination of screw, rubber grommet and "velcro." The trick is to be gentle as it's easy to break the damn things. Only the "velcro" one needs a bit of strength as they really do snap on and off.

Posted on Feb 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Kawasaki ZZR 1400 won't shift


Hi, Edward and the usual suspects are:
1. Clutch not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
won shift up to 2nd
Shift Lever is stuck Cant get past 2nd Kawasaki Forums
Kawasaki 2007 ZZR1400 Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Jun 10, 2017 | 2006 kawasaki ZZR 1400

1 Answer

What are the two spare wire with bullet connectors for under seat of zzr 1400


Hi, Wilma it may be for an accessory connection for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kawasaki, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
ZZR International View topic Fitting Oxford Heated Grips to me zzr
Modifications ZZR 1400 Touring
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Jan 06, 2017 | 2006 kawasaki ZZR 1400

1 Answer

Why could Kawasaki zzr 1400 cut out on higher revs before reaching its limiter? And when I switch of the bike and on again in the drive it goes again. And n few minutes later does it agai?


Hi, Elanza the following applies to carbureted also fuel injected models and the usual suspects are:
1. Severely discharged or a damaged battery, 9 volts or lower.
2. Faulty alternator/generator and or voltage regulator.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system and or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, O2, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Water or dirt in the fuel system, carburetor or filter.
9. . Restricted, blocked or kinked fuel line.
10. Fuel tank empty.
11. The gas cap is not venting properly or fuel tank venting system blocked.
12. A faulty Fuel Pump, pressure regulator and or fuel injectors.
13. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
14. Needle and seat stuck closed in the float bowl.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
http://fullmanuals.com/search/?q=Kawasaki+zzr+1400

Nov 08, 2015 | kawasaki Motorcycles

1 Answer

Why could Kawasaki zzr 1400 cut out on higher revs before reaching its limiter?


Hi, Elanza and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your question please visit the website below. Good luck and have a nice day.
http://fullmanuals.com/search/?q=Kawasaki+zzr+1400

Nov 07, 2015 | kawasaki Motorcycles

1 Answer

What could be the problem? I have a ZZR 1400 and after the last 2 ride outs, when I have stopped, the expansion tank empties?


Hi Brian it could be a weak radiator cap, check this first after this you may need to go to a mechanic to check head gasket.

Apr 06, 2015 | kawasaki ZZR 1400 Motorcycles

1 Answer

Kawasaki zzr 1400 engine oil


Yes Castrol Power 1 is fine. I use it all the time

Jul 27, 2012 | 2011 kawasaki ZZR 1400

1 Answer

I have a 2009 zzr 1400 with a bad flat spot between 3 and 4 thousand revs, has just started, any help please


2 and 3 thousand RPM will lug this bike depending on what gear you are in. You could also have a timing or vacuum issue if it's a hesitation when you twist it. I'd run a can of Seafoam through a tank of gas first to clean the fuel system, intake valves and combustion chambers. Hope this helps.

Jul 03, 2011 | 2010 kawasaki ZZR 1400

1 Answer

Where is the ecu on a kawasaki zzr 1400


Remove the seat and its towards the rear tail section, there is a box on top of it, below you';; see a bigger box that has two big leads going to it, if you need a picture I have one.

Apr 30, 2010 | 2006 kawasaki ZZR 1400

2 Answers

I cant seem to get the seat off my kawasaki zzr 1400..the key just seems to unhook a little hook...


Hi. Sorry but rho is wron on this one!
The lock you are using is just for the helmet lock. The seat lock is out of sight underneath the nearside rear coloured seat trim. The key is inserted pointing straight up!

Mar 20, 2010 | 2006 kawasaki ZZR 1400

1 Answer

ZZR 1400 wiring identification assistance


Try this site look for zzr 1400 wiring diagrahm http://www.mediafire.com/?81yj7rotpej Hope i helped pwalsh.!!.....

Nov 10, 2009 | 2006 kawasaki ZZR 1400

Not finding what you are looking for?
2011 kawasaki ZZR 1400 Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...