Question about 1980 Suzuki Gs 550 L

Open Question

How 2 replace a hayabusa cluth push rod seal - 1980 Suzuki Gs 550 L

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cape cod bob
  • 292 Answers

SOURCE: splitting hayabusa forks

no. but go here for a free pdf service manual which will tell you http://www.carlsalter.com/motorcycle-manuals.asp

Posted on Apr 12, 2009

  • 3567 Answers

SOURCE: there is an oil leak from the push rod so i am

The only push rod in your bike is the clutch push rod. It is on the left side of the engine and between the flywheel and the chain sprocket. Just remove the left side chain cover to gain access to the rod. Pull the rod out of the center casing then use a screwdriver to pry the old seal out. Then just put a new seal in its' place and re-install the rod. The rod will not need to be replaced unless it is bent or is pitted from rust where it runs through the seal.

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace clutch push rod seal on 07 hayabusa


Hi remove the slave cylinder on the left hand cover then withdraw the rod. If its broken on that side drain the engine oil and remove the clutch cover. Then the clutch pressure plate then you will have access to the rod. Regards Jim...

May 19, 2015 | Motorcycles

1 Answer

My hayabusa engine having a loud konck noise after rebill it and change crank-rods and bearing .


sounds like the person who rebuilt the motor did not check the clearance on the rod bearing or the crank bearing. bring it right back to them.

Oct 04, 2014 | 2000 Suzuki GSX 1300 R Hayabusa

1 Answer

Clutch push rod problems


pull the slave cylinder off and push the piston back in the cylinder then replace all should be ok.

Mar 15, 2014 | 2002 Suzuki GSX 1300 R Hayabusa

2 Answers

I have a 1974 DT 360 motor will start and runs fine. But the clutch will not disengage to shift or stop the bike, i was wondering if there was a 3 piece clutch push rod constisting of an inter push rod, a...


I can't find any parts diagrams for a DT360, and it has been 35 years since I worked on a DT360 at LYNN'S YAMAHA, DM Iowa, but as I recall there IS a ball bearing in the assembly. It went in right before the pushrod. The diagram below is for a 1978 DT400. I am pretty sure your 360 has the same clutch assembly as the 400. The ball bearing would not have worn down. A prior owner leaving it out is far more likely. Please take a moment and rate my answer. Thanks. tombones49_72.gif

Apr 14, 2011 | 1972 Yamaha DT 360

1 Answer

Shifter for mannual cluth moves around like a joy stick and won't go into gear. What happened. I had to push car to get it out of street.


sounds like the connection rod has came off on the gear box if you look or feel on the gear box you should see or feel 2 rods these connect to the shifter one of them will be stiff the other will be floppy feel waer the stiff one connects to and close to it there will be a ball you need to push the floppy rod back on to the ball it mite come back off again what i did when mine went was i but a cabe tie round it to hold it on hope this works for you to .

Jan 18, 2010 | 1998 Saturn SL

1 Answer

There is an oil leak from the push rod so i am trying to replace the rod and the seal... thing is i don't know how to do that


The only push rod in your bike is the clutch push rod. It is on the left side of the engine and between the flywheel and the chain sprocket. Just remove the left side chain cover to gain access to the rod. Pull the rod out of the center casing then use a screwdriver to pry the old seal out. Then just put a new seal in its' place and re-install the rod. The rod will not need to be replaced unless it is bent or is pitted from rust where it runs through the seal.

Oct 05, 2009 | 1980 Suzuki Gs 550 L

2 Answers

Suzuki gsx600f clutch problem


if it is in gear for sure and it doesnt move even with the clutch engaged maybe you are missing a piece inside the clutch like the clutch boss spring. or possibly your plates are worn so much they wont hook up. or you are using a very poor grade of oil. Dont take my absolute word for all these solutions but these may lead to some problems like that.

Aug 16, 2009 | 1991 Suzuki GSX 600 F (Katana)

1 Answer

What kind of parts are insde the chain sprket cover where the cluth line enters the case . My cluth line is tight not engageing. I looked at pictures on the ent apartently im missing like a a piece of...


This is inside the casing cover. Just a lever for the clutch cable to connect to, a spring, The clutch release mechanism, a seal and a clutch push rod. The clutch release has a threaded screw for adjusting the clutch and a locking nut for the screw. The only other thing is a metal bracket.

What exactly is the problem? The lever is hard to pull? The clutch won't engage to make the bike go forward? The clutch will not dis-engage, the motor will not stop driving the bike forward? What?

001fe3a.gif

Aug 14, 2009 | 2002 Suzuki GSX-R 600 M

1 Answer

Splitting hayabusa forks


no. but go here for a free pdf service manual which will tell you http://www.carlsalter.com/motorcycle-manuals.asp

Apr 12, 2009 | 1999 Suzuki GSX 1300 R Hayabusa

Not finding what you are looking for?
1980 Suzuki Gs 550 L Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...