Question about Motorcycles

Open Question

How do I remove a gear shift drum 450 2002 Honda foreman

Go into reverse neutral1st won't go any higher

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: electric start wont work 2000 honda

Check the starter switch (button) .

Posted on Jul 23, 2009

Ad
  • 860 Answers

SOURCE: wont shift from neutral to upper gears

check to see that lever isn't fouling anywhere on the way up, you may have to re-position the lever on the splines to sit lower

Posted on Jun 06, 2010

early93
  • 177 Answers

SOURCE: Gear Shift won't go into park. Shifter real

Something with the shift linkage is messed up.

Posted on Jun 10, 2011

  • 107 Answers

SOURCE: I have an 04 yz 125 that won't shift into 2nd but

2nd gear is at the bottom of the shafts if the tranny is stacked in the mag side case. So it is controlled by the bottom fork. You should be able to shift it thru all the gears by turning the shift drum. Make sure as you shift the shafts stay all the way in the output shaft and idler shaft bearings. As you shift it, look for full mesh between the wheels(shaft that goes to the clutch) and the gears across on the output shaft.
If that all looks good, the shifter cluster(on the end of the shift drum, with the 2 dogs that engage the notched wheel on the end of the drum) may not be lined up properly. If the gears and shift drum are new, I'm thinking I'd look there first. Good luck!

Posted on Jun 11, 2011

  • 3567 Answers

SOURCE: My husbands Honda cx motorcycle won't go into

It sounds like a bent shift fork in the transmission. Somewhat expensive to fix and the repair is not recommended for the novice mechanic. Some special tools are required as well.

Posted on Jul 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peg perego john deere power pull won't go in reverse


are both wheels spinning in forward gears? if not you have a bad motor

Mar 11, 2013 | Toys

1 Answer

Freelander 2002 transmition won't go in reverse what can i do


Check the fluid.

Is the engine light on??? Yes? Diagnose....

No.......... it's broke

Feb 20, 2013 | Transmission & Drivetrain for Land Rover...

1 Answer

My 1995 Cadillac Deville won't shift out of first.


Sounds like a bad shift sylenoid try flushing it but it might be to late

Dec 04, 2012 | Cars & Trucks

1 Answer

Air Compressor will only pump up to 35lbs.


The two main areas to inspect if your pressure isn't going over 35psi are the valve plate and piston/cylinder assembly. If the reed valves on the valve plate are bent, warped or broken, usually attributable to high heat, they won't seal well enough to get higher pressures. If the cylinder is badly scored or the piston and/or piston rings are damaged, usually attributable to running the pump motor with low or no oil, the seal between them won't be good enough to get the pressure any higher.

Aug 13, 2012 | Craftsman Air Tools & Compressors

1 Answer

2008 Saturn vue won't go out of park and shows it being in reverse and won't start.


Broken shift cable ?
If the neutral safety switch is on the transaxle and the cable is broken, the switch could still be in the reverse position.

Jul 05, 2012 | Cars & Trucks

1 Answer

My rebuilt transmission won't go forward?


i would be checking the shifter cable adjustment first see how that goes goodluck

Sep 18, 2017 | 1992 Ford F250

1 Answer

I have a craftsman riding mower that's 2 years old and it won't go into gear it's a 6 speed won't go in reverse either


Hi, did this happen when you went to use it or while mowing? Also will the lever go in but the mower won't move or won't the lever go in either gear at all? Regards Phil.

Aug 17, 2011 | Craftsman 42" Briggs Stratton 20 hp Gas...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...