Question about 1995 kawasaki ZX-6R Ninja

Open Question

1995 kawasaki ninja zx600 - 1995 kawasaki ZX-6R Ninja

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
johnsadam199
  • 3 Answers

SOURCE: oil change 1995 kawasaki ninja

you need to put on service stand and pull out oil plug after draining oil filter and drain all engine oil put new filter in and us sae 10 w 40 oil

Posted on Apr 13, 2009

Ad
yammy_alf
  • 666 Answers

SOURCE: how do I clean the carborator on my 1994 kawasaki

Carburator Theory and Tuning
carb_jet_usage1a.jpg

For some reason everyone seems to think tuning a carb is just real easy. Change a jet or two and boom, your there. Yeah, right ! There are quite literally millions and millions of jet combinations. A rough check on Bing carbs shows there are at least 13,860,000 different combinations of jets. If you are going to change carbs you'd better be prepared to spend some time and money on the job.
venturi1a.jpgmainjet_1a.jpgIf you look at a carburetor, you will notice a rather large hole going from one side to the other. This is called a Venturi. Air passes into the engine through this hole (Venturi). As the velocity of the air entering the carb (and then the engine) increases, it's pressure decreases, creating a low pressure or vacuum in the venturi. This vacuum moves around in the venturi, as the throttle is opened, and sucks gasoline through the different jets in the carb. The gas then mixes with the air going through the venturi. The way the jets are made causes the fuel to vaporize as it goes into the venturi. Where the jets are placed in the carb and where the jet's outlet is located in the venturi, determines what part of the throttle opening that jet controls. The idle jet system (comprised of pilot air jet, pilot fuel jet and pilot fuel screw) controls from 0% to about 25% of the throttle opening. The throttle valve controls 0% to 35% of the throttle opening. The needle jet and jet needle control from 15% to 80% of the throttle opening and the main jet controls 60% to 100%. This means that when you open the throttle about one eighth of the way open, all of the gas/air mixture going into your engine is controlled by the idle jet. As you can see, the different jets over lap the operating range of each other. That is, the jet needle starts to effect things before the effect of the idle jet ends. This is something to remember when working on carbs... everything is interconnected. Change one thing and it will effect other things.
OK, let's go over the different systems in the carb and see what they do.

  1. Fuel level. The fuel level is controlled by the fuel floats and the fuel float valve. The floats are hollow or made of something that will float on gasoline, such as cork. Part of the float presses against the float valve, sometimes called a needle and seat. Most times the part of the float that touches the float valve needle is bendable so you can adjust the level of the fuel in the floatbowel. All plastic floats are not adjustable. If this level is way too high, gas can leak out the carb overflow tube or into the engine. If fuel gets into the engine it will thin out the engine oil, ruining it's ability to lubricate. This will, sooner or later, blow up your engine ! If a full tank of gas in the evening turns into a half tank by morning, check your oil. If it's thin and smells like gas, change it and replace your float valve and/or check your fuel level. If the oil is OK, check under the overflow tube. If it's OK, then check where you are parking your bike 'cuse someone is walking away with your gas ! If your fuel level is just a bit high, the mixture will tend to be a bit rich. If it's low, the mixture will tend to be a bit lean. This is because a high level takes less vacuum to **** fuel into the engine and a low level takes more vacuum to do the same.


  2. Pilot or idle jet system. The idle jet controls the idle and on up to quarter throttle, give or take a bit. On some carbs, like Mikuni there is an air jet too. In conjunction with the idle jet there is an idle jet air screw. This screw leans or richens the fuel mixture for a smooth idle and on up to one quarter throttle. From the idle jet, there are little passages cast into the carb that lead to holes just in front of the throttle valve or plate. There can be just one hole or there can be several, depending on the carb design. They effect the mixture as long as the vacuum, in the venturi, is over them. As the throttle opens further, the vacuum moves to the needle jet and jet needle.
  3. The Throttle Valve. The big slide that opens and closes your throttle has a bevel angle cut in one side of the big round (can be flat, too) slide, toward the air cleaner. This angle comes in several sizes and helps control the fuel mixture from idle to about 35% open throttle.
  4. Needle Jet. This jet doesn't really even look like a jet, but it is ! It controls the fuel mixture from 15% to 60% open throttle. It sets in the center of the carb, right over the main jet.
  5. Jet Needle. This is the needle that rides in the throttle slide and goes into the needle jet. This needle controls the fuel mixture from 20% to 80% open throttle. It can come in many different sized tapers. Sometimes, one needle can have several tapers on it. The top end of the needle has grooves cut in it, usually five, and you can move the little clip on the end up or down to lean (down) or richen (up) the mixture. Most late model bikes have needles with only one groove cut in them. This is so you can't richen the mixture, thereby keeping the EPA happy.
  6. Main Jet. This jet controls the fuel mixture from 60% to 100% open throttle.

Posted on Apr 16, 2010

nedkelly900
  • 345 Answers

SOURCE: picture of the ignition wires and where they go on

Is this the one you need ,ignition coils?
363071c.gif

Posted on Jun 14, 2010

  • 403 Answers

SOURCE: I'm planning on purchasing a

there is only 1 vin on the bike, if your planning on registering it your gonna need it. The only other way would be to locate the frame number and have a kawi dealer cross reference for a vin, but being 6 years old, might not be able to. cant the owner just get it off his registration for you ? aslo, becarefull of receiving stolen property, sounds like an issue to me.

Posted on Mar 19, 2011

rzman
  • 148 Answers

SOURCE: 1995 Kawasaki Ninja 250 will only run with the

you have blocked jets in the carbs,,the carbs need to be removed and cleaned.

Posted on Mar 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Main and big end bearing torque


Hi, Peter for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kawasaki, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://dwulet.com/bikes/docs/zx6rtorque.htm
http://www.zxforums.com/forums/mechanical-technical/111450-crank-bearing-question.html
http://support.bazzaz.net/service_manuals/ZX6RR03kitmanual.pdf
1995 1997 Kawasaki Ninja ZX 6R Service Manual ZX600 F1 F2 F3 Moto Data...

May 09, 2016 | 1997 kawasaki ZX-6R Ninja

1 Answer

What kind of test does the pulsar on required1994 Kawasaki's ninja zx600 e to check if its good or bad


If the bike just cuts out whilst riding and wont start straight away but will when it cools down its the pick up for sure.
You cant test it they only fail when hot

Feb 05, 2015 | kawasaki Motorcycles

1 Answer

How to replace starter on 94 ninja 500


KAWASAKI NINJA ZX 500 Service and Repair Manual PDF Download
KAWASAKI NINJA ZX 6 ZZR600 ZZR500 ZX500 D1 D2 ZX600 E1 E13 1993 1994...

These manuals are your number one source for repair and service information. They are specifically written for the do-it-yourselfer as well as the experienced mechanic. Using this repair manual is an inexpensive way to keep your vehicle working properly. Each manual provides step-by-step instructions based on the complete disassembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure.

Jan 10, 2014 | kawasaki Ninja Zx7r Zx9r '94 To '04

1 Answer

What Kind of battery do I need for this bike?


OEM Type:
Yuasa #YTX9-BS Motorcycle Battery for Kawasaki ZX600-FA Ninja ZX-6R - 600cc (2008-2011)

Jan 20, 2012 | 2008 kawasaki ZX-6R

1 Answer

Could you the tyre pressures front and rear for a kawasaki ninja 600 year 2000 please .thanks


hi, in there wisdome kawasaki played around with tyre sizes on the zx6r ninja,

tyre size rear 160/60/17.
tyre size front 120/60/17 1995-98 models zx600f

rear. 170/60/17
front 120/60/17 1998-2000 models zx600-g1

rear 180/55/17
front 120/65/17 2000-01 models zx600j

the only thing they didnt play around with is the tyre pressures all models front 36psi or 2.5 bar
rear 41psi or 2.9 bar

hope this helps and thanks for using fixya.
paul

Jan 30, 2011 | kawasaki ZX-6R Motorcycles

1 Answer

91 zx600 ninja voltage regulator


they are all pretty close, check the plug shape and the different colored wires going in. most stators put out similar voltage and amps, it should have three yellow or white which are the ac voltage and a red and a black for positive and earth, if there are other colors as well make sure the replacement has the same

Apr 04, 2010 | 1995 kawasaki ZX-6R Ninja

Not finding what you are looking for?
1995 kawasaki ZX-6R Ninja Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...