Question about Triumph Thunderbird Motorcycles

1 Answer

Fitting gear sharft

Replacing gear shaft

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There are at least two gear shafts, please specify. In general, this kind of repair requires someone that has proper knowledge, training, and tools to complete properly.

Posted on Dec 10, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fribatting and thummping noise underneath in 2004 landcruiser


The front tail shaft of the cruiser is prone to spline wear and failing U-joints. have the drive shaft inspected and replace if it cannot be repaired

Nov 24, 2013 | 2002 Toyota Land Cruiser

1 Answer

Repair gearbox sharft


Each prop shaft from different manufacturers is removed diferently. But- once out - a press with a couple wood blocks can straighten it provided it is just a slight wobble. If the prop can not be put on, it should be replaced.

While its out check the area the seal rides and see if it is worn badly. If a deep grove and it's shedding metal, you should replace it. I've had no luck with "speedy sleeves" in a marine environment.

Jan 21, 2012 | Boating

1 Answer

Wat is the sharft called that the gear leaver sits on and where could i get one asap


Technicaly it is designated " Lever-comp-change shaft ". Ask the parts counter for that and they will kinda look at you funny. Generally they are called a " shift shaft ". Your Kawasaki dealer should have one or you can go online to Babbitt's and get one there. www.babbittsonline.com tombones49_2.png

Jun 19, 2011 | 2003 kawasaki KX 250

1 Answer

Need help to realine tail sharfs Nisan Twin cab 1998 D22 Have a vbration when excelerating. Have put new clutch in and forgot to mark where tail sharft aligns


check your center support bearing on the shaft assembly. its most likely broken. its somewhat in the middle og the drive shaft. it has rubber boot. something tells methat the boot is torn and bearing has play in it. check and replace if you see separation/beeing broken.

Jun 03, 2011 | 2007 Nissan Frontier SE Crew Cab

1 Answer

Gearbox sharft loose


Something inside the gear box it broken or has dislodged, or possibly a mount for it has come loose and is broken or missing.

Jan 05, 2010 | Mitsubishi Tredia Cars & Trucks

1 Answer

Engine pull apart


you need to get a puller they are just pressed on by the harmonic balancer there is a key and a tapered fit.

May 20, 2009 | 1986 Nissan Stanza

2 Answers

Gear slipping in dewalt dw056


Those gears are only held on the motor with their tight fit, if yours is slipping that easily the motor will have to be replaced. The new motor will have that gear on it.

Apr 07, 2009 | Dewalt DW056 18 Volt Cordless Impact...

2 Answers

2005 yz 250 shifting problems


Well. I'm a motorcycle mechanic and my 2004 RMZ 250 recently did the same thing, The Shift forks inside my transmission actually bent and were not moving the gears as far as they needed to go and eventually got to where it quit shifting all together, recently also repaired a CR 125 That wouldn't shift at all and it was the shaft the shift forks go on was bent and hung the shift forks. Sounds like your shift forks are bent to me though.

Mar 14, 2009 | 2003 Yamaha YZ 250

1 Answer

How to remove gear from arbor shaft on cut off saw?


The fact that there is no screw suggests its a push fit. Without knowing the machine, I am taking an educated guess, but suggest you will need a hydraulic press.

Feb 27, 2009 | Hitachi CC12Y 12" Portable Cutoff Saw

1 Answer

Cord stayes out motor not running


Take it back to place of purchace.
We get these all the time if its the cheap bent sharft with starter between shaft and motor. the easy start spring gets jammed and needs replacing.

Dec 26, 2008 | Garden

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...