Question about Ducati 749 S Motorcycles

1 Answer

Stalls when bikes put in put in 1st. replaced my batt with a lithum ion one, starts up right away. Any ideas what's happening here and why?

Frustrated that I cannot get my duc to go. Replaced my clutch this summer with the batt. Returen from a tripp (approx a month) and she wouldn't turn over. I replaced it with a lithum ion batt today and she fired right up, however my original problem remains. As soon as I drop it 1st it cuts out, if I stat it in 1st it lunges foward but never turns over. Been lloking online for clues but nothing. Any Ideas?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ducati Master
  • 8,404 Answers

You probably already checked this ... is your side stand down when the engine stalls? Many bikes have a safety interlock switch the kills the engine if the side stand is not in the proper stored position when the bike is put into gear.

Posted on Dec 10, 2012

  • Anthony Dec 11, 2012

    Yes, I've ensured my stand was up while engaging 1st gear.

  • Anthony Dec 11, 2012

    Tried something this past weekend I jumpered the plug that contains the safty switch on the kick stand. It started up easy enough and was able to shift into 1st it moved a little WITH THE CLUTCH PULLED IN. What's up with that? I let out the clutch and forced a stall out.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Motor shuts off as soon as I start to accelerate.

Might be a fault in the side stand sensor, you cant go far with the side stand out, or if the sensor has not sensed the stand is up.

Posted on Mar 18, 2009

  • 1 Answer

SOURCE: v-star 1100 custom stalls when dropped into 1st gear

did u make sure the kickstand was up

Posted on Apr 12, 2009

bozcro
  • 867 Answers

SOURCE: 06 m50 sat for approx 6 months charged the battery won't start.

from your description, i would sugest you make sure fuel is getting to the injector unit, remove the fuel supply hose.if you have spark at the plugs and fuel getting to the injectors you have isolated the problem. i would also drain the old fuel when you take the hose off and fill the tank with high grade fuel. bikes dont like old gas.

Posted on Jul 21, 2009

czaa
  • 4514 Answers

SOURCE: 2007 Hyosung GT250R stalling in 1st

clutch needs ajust cable wise or internal-they r similar to ***-chec library sec 629 if no manual is sold

Posted on Aug 17, 2009

  • 28 Answers

SOURCE: 07 gsxr 600 cuts out at 10,000 rpm drops suddenly

chech side stand swich

Posted on Aug 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car wont shift out of 1st gear then stalled and woudn't restart after about 20 minutes car did start and shifted fine any ideas


You need to get this to the dealer for electronic system diagnosis and testing to figure this out, it will happen again.

Jun 15, 2012 | 1997 Dodge Stratus

1 Answer

Yamaha MT03 - shorting / or loss of power


Hi, David check all wire connectors in the ignition and starter circuit and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Yamaha MT Owners Club
What to do When Your Motorcycle Won Start
Yamaha MT 03 Service Manual
OEM parts for Yamaha
YAMAHA MT 03 Owner Manual

Mar 08, 2017 | Yamaha MT-03 Motorcycles

1 Answer

88F250 4x4 5.8L FI 5 speed. A friend has this & the starter went out. I replaced it & the solenoid. No big deal right? I returned it & the next day he called me & told me that the...


Its a solenoid...it engages the bendix and truck starts...bendix should retract because power to it gets shut off by ignition switch going to "run".

Only way bendix would stay engaged or get a signal to keep turning ???
Bad contacts in ignition switch...maybe ??
Start relay in under hood power distribution panel has hot or welded contacts ?

I've gotta think about this one...hope this gives some help...

Jul 30, 2011 | Ford F-250 Cars & Trucks

1 Answer

How do I replace the fuel filter - 92 honda 750


hi Mike....does it stall when you let clutch out or when you put in gear?....i would look at the side stand kill switch!!! as this maybe stuck with not being used....hope this helps

Feb 11, 2010 | 1992 Honda CB 750 Nighthawk

1 Answer

2002 suzuki rm 125 shift drum placement, shifting problems,


go to your local shop and ask them to photocopy you pages out of manuel for setting of shift drum

Jul 09, 2009 | 2003 Suzuki RM 125

2 Answers

Gear/clutch problem


does not seem like the waterpump. is the clutch set too loose?
usually in wire based clutches, if the clutch cable is set to be too loose, or if it is frayed, and needs replacement, the bike will jump and stall.
check that.

Dec 10, 2008 | 2003 Suzuki RM 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ducati Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

bobkoure

Level 1 Expert

36 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Are you a Ducati Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...