Question about 2011 Sym VS 150

1 Answer

Parts of rear wheel assembly - 2011 Sym VS 150

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Sym Master
  • 8,404 Answers

What parts ... ???

Posted on Dec 06, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why am I able to shake my back tires?


Yes , your wheel bearings are bad !!!!!!

May 25, 2015 | 1998 Cadillac DeVille

1 Answer

Emergency brake adjustment


This depends on which cable is hanging down. There are several cables in the assembly. One cable comes from the parking brake assembly under the Drivers' dash. It joins the rear cable assembly that goes to each rear wheel. Some cars have 2 separate rear wheel cables and others have a Y assembly that has to be replaced as 1 part.

There can be an adjustment rod where the front cable meets the rear assembly. Some of the parking brake reels under the dash are suppose to reel in extra slack.

Often if the rear Emergency brakes are worn out, there will be slack in the assembly.

Sep 08, 2014 | 1998 Lincoln Town Car

3 Answers

Where is the abs speed sensor located on a 2005 pacifica?


Behind each of the front wheel hub

Have to follow the wires to find the rear sensors

The internet should have a picture,easier to just look under the car

Jun 10, 2014 | 2004 Chrysler Pacifica

1 Answer

What does the rear wheel assembly diagram 1993 flhtc look like


Easiest way to find out. 1)Put your smart phone in pocket. 2) Go to nearest Harley-Davidson dealership. 3)Go to parts department. 4)Ask friendly parts counterman to look up wheel assembly in parts manual. 5)Ask friendly parts counterman if you may take a photograph of wheel assembly. 6)Take several photographs of wheel and friendly parts counterman. 7)Thank parts counterman profusely! Or go to the same dealership and order a copy of the parts manual for the 1993 FLHTC

May 17, 2014 | 2003 Harley Davidson FLHTC Electra Glide...

1 Answer

SPRING URETHANE BLACK 12.7MM ID X 25.0MM OD X 38.1MM TH , DUROMETER ; SHORE 95A, B-116-064 for my jazzy 1107 Power Chair are cracked and busted causing my rear wheel caster assembly to lean backwards in...


I know that 95 durometer EVA is available from other sources like shoe findings suppliers. This is about 1/2" by 1" by 1.5" and if a mechanic was able, he could fix you up with that. If that is what you need, they could help you out without having to replace the whole assembly.

Feb 28, 2017 | Health & Beauty

1 Answer

How to change a rear wheel bearing on a 2004 ford taurus???


How to Replace Rear Wheel Bearing/Hub Assembly on a 2nd generation Taurus

The following procedure is for a Ford Taurus (VIN S), with rear drum brakes and ABS.

1. Loosen wheel lug nuts, raise rear of vehicle, and support securely on jack stands. Block front wheels and remove rear wheels.

2. Remove brake drum (parking brake must be off).

3. Remove and clean ABS Sensor (Torx E8) with a spritzled rag.

4. Remove grease cap from hub.

5. Remove and discard hub retaining nut (36 mm). This is a compound nut, comprised of several nuts inside a metal cage. Use a 36 mm axle nut socket (e.g., OEM 25206). Many auto parts stores will lend you this socket. A 1/2-inch drive air impact wrench or breaker bar is necessary to remove the nut.

6. Remove wheel bearing/hub assembly from spindle. It easily comes off by hand.

7. Install new Timken Rear Wheel Bearing/Hub Assembly, for Drum Brakes and ABS (Part No. 512162). Tighten new axle spindle nut (Dorman 05114) 221 lb.-ft., replace grease cap, and button everything up.

Jun 22, 2012 | 2004 Ford Taurus

2 Answers

Where can I get parts for tractor


http://www.sprinklersupplies4less.com/traveling-sprinklers-nelson-1865-replacement-parts-c-384_627.html

Part suppliers are very limited for this item. And it was the only place I found other than the LR Nelson manufacturer.

Jun 06, 2011 | Nelson Sprinkler: Traveling Tractor

2 Answers

Where wheel speed sensor is located on 2001 pontiac grand am se


2001 Pontiac Grand Am 2.4L SFI DOHC 4cyl

Vehicle Speed Sensor - Location:
The speed sensors are built right into the wheel bearings of your vehicle, at the front and rear locations. They work both with the anti-lock brakes and with the traction control systems on the vehicle.

Removal & Installation
Front
The front wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Front Suspension for service procedures.
Rear
The rear wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Rear Suspension for service procedures.

I hope help you with this (remember rated this help) Have a nice day, good luck.

Sep 23, 2009 | 2001 Pontiac Grand Am SE

Not finding what you are looking for?
2011 Sym VS 150 Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sym Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Dave Matthews
Dave Matthews

Level 2 Expert

97 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

Are you a Sym Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...