Question about Suzuki Motorcycles

Open Question

How to set tps on 1998 vl1500 - Suzuki Motorcycles

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1998 Suzuki VL 1500 Intruder fuel light stays on

Hi, Mark and the usual suspects are:
1. Faulty sending unit.
2. Faulty wiring between sending unit and light
3. Fuel light circuit grounded.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Low Gas light always on WTF
Low Fuel Light Stays On Help
Suzuki VL1500 Service Manual
Suzuki Intruder VL1500B Owner Manual

Mar 28, 2018 | 2000 Suzuki VL 1500 Intruder LC

1 Answer

Suzuki VL1500 Intruder LC main fuse location

Hi, Thimothy for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Suzuki VL1500 Intruder LC main fuse location Google Search
fuse box loc suzuki intruder 1500
Suzuki VL1500 Service Manual
OEM parts for Suzuki
Suzuki Intruder VL1500B Owner Manual

May 15, 2017 | 2001 Suzuki VL 1500 Intruder LC

1 Answer

How to start floded engine 1998 ford f150 truck 4.2 engine

The (TPS) throttle position sensor realizes there is a flooded condition when the operator presses the pedal to the (WOT) wide open throttle position. However, the usual cause is a bad TPS. Replace the TPS, not a difficult job two screws and an electrical plug.

Jun 16, 2014 | 1998 Ford F150 Regular Cab

1 Answer

Setting idle

If you have carbs:

Part #60 adjusts both carbs' idle speed evenly.

If you have throttle bodies:

Part # 14 should adjust the idle speed on both.

Apr 20, 2014 | 2005 Suzuki Boulevard C90

1 Answer

How do I set the timming on a 1400 Nissan sentra 1998 model

This is for a 1998 nissan sentra 1.4 engine, start engine and allow to reach operating temp.then turn engine off and disconnect throtle postion sensor connector.

With tps sensor disconnected start engine and increase idle to 2000 rpm three times then release and allow it to idle.

now check timing, timing should be at 6-10 degrees BTDC. adjust as needed then turn key off and reconnect tps .
Good day.7_15_2012_4_06_52_pm.gif7_15_2012_4_07_06_pm.gif

Jul 15, 2012 | Nissan Sentra Cars & Trucks

1 Answer

Where is the tps on a 1998 plymouth voyager

The Throttle Position Sensor (TPS) is mounted to the side of the throttle body and connects to the throttle blade shaft. The TPS is a variable resistor that provides the PCM with an input signal (voltage).


Fig. Pull the Throttle Position Sensor (TPS) off of the throttle shaft

Hope this helps (remember to rate and comment this free answer).

Jun 22, 2011 | 1998 Plymouth Voyager

1 Answer

Replacing front fender which model would i pick?

I am not sure what your asking but I am assuming what models will work. 1998-2003 models of vl1500 I know for sure 2004-current vl1500 and c90 boulavard may work as well I am about 90% sure they will but not 100%. I hope this is the information you are looking for.

Nov 25, 2010 | 2001 Suzuki VL 1500 Intruder LC

1 Answer

I need to set the RPM a bit higher can it be done manually or is it set electronically.

Check the parts on the airhorn behind all the airfilter ductwork. On one side you will have a TPS switch. It has 2 screws and 1 electric plug. If you take it off for a second you can see if there is a elongnated slot for 1 screw. This will raise the RPM slightly by adjusting the TPS in that elongnated slot.

On the other side of the airhorn there is a stubborn set screw. It butts up to the throttle cable. This will adjust the RPM beyond the range of the TPS base idle. So to answer your inquiry the TPS can be manually adjusted to electrically raise RPM, the stubborn set screw can manually be adjusted to raise RPM.

Nov 04, 2009 | 1998 Mercury Mystique

2 Answers

1998 Dodge Ram 4X4 Quad 5.9L Auto. When accelerating slowly, shift fine until up to a cruizing speed, then keeps shifting up & down like into/out of a passing gear. Going up hill under a slight load...

Mr. dodge ram, with the 46re trans the pcm needs a signal from the tps sensor to monitor throtlle opening, accel and decel, what has happened the tps has a worn out spot in cruise area, hence the down shift, uphill is fine because your past the worn out spot, replace your tps sensor, its mount on left side of throtlle body , 2 screws, 1 connecter, and its out, when done turn key on, eng off, step on gas pedal 6 times slowly, then turn off key, this will help set min tps setting, GOOD LUCK RDJRP

Jul 31, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

79851 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4898 Answers


Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides