Question about 1991 Suzuki VS 1400 Intruder

1 Answer

Lights keep blowing the fuse

The head lights were replaced with a tri head lights from a harley and keep blowing thew fuse.....is it ok to put in a larger fuse ? this is a 1996 suzuki 1400 intruder.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You can pull the light apart and check the amperage they require since they are not the factory headlights they most likely have a higher amp requirement and find out what that is and then install the proper required fuse for them. Also be sure to check and see if the wires are properly hooked up and wrapped properly and are not grounding out on any metal or other wires. This should solve your problems. Might also want to see if the headlight relay is also the proper one to cover the amps they require as well. Hope this works for u and good luck

Posted on Feb 19, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Clutch bleed on a Suzuki 1400 Intruder 2000

One the left-hand side of the bike (facing forward), there is cover plate just ahead of the drive shaft. Remove that cover (mine has 8mm bolts). The bleeder valve is under this cover. Go to an auto parts store and get a "one man bleeder kit" or if you have some plastic tubing that will fit over the valve, you can use that and a clean jar. Follow the instructions on the bleeder kit, or if you're using the jar and tubing, fill the jar about a quarter of the way with break fluid (use DOT4, but never DOT5!). Take the cover off the master cylinder up at the handlebars, place the tube over the end of the bleed valve (after loosening it a turn or two. Place the other end of the tube down in the break fluid in the jar. Work the clutch lever until you stop getting bubbles in the jar. Be sure to keep the fluid level up in the reservoir. Tighten the bleeder valve, remove the tubing, top off the fluid and replace the covers.

Be careful not to get brake fluid on anything. It will eat paint and mess up other things.

Posted on Feb 13, 2009

  • 2336 Answers

SOURCE: How well does the Suzuki 1400 cc Intruder handle?

The Intruder does handle fairly well compared to its' counterparts of the cruiser class, by handling I would assume your talking about how well it behaves in turns...since this class of machine IS the cruiser type do not expect to keep up with the current or past generations of sportbikes as you will fall behind. The best scenario is SMOOTH sweeping turns, the suspension in its' current form cannot deal with irregularities in the road...sportbikes' suspensions are meticulously calibrated for these real world curcumstances...cruisers cannot do this. The raked out front forks of cruisers make for a very stable platform but are not designed to be turned hard. A simple modification that I would myself do if I had a cruiser, would be the addition of a fork brace...a chunk of aluminum that strengthens the two front fork tubes..so that they don't flex (As much!). In addition I would pay attention to the exaust setup, footpegs and any other hard parts that would interfere with agressive cornering(Lean angle).Some exausts hang SO far down on cruisers that they really limit how far you can bend er over...all that stuff needs to be removed, changed or modified so you can corner good up to the suspensions limit.

Posted on Nov 10, 2008

emissionwiz
  • 75066 Answers

SOURCE: how many spark plugs does a suzuki intruder 1400

under the gas tank, remove the gas tank to replace them, it has 2 plugs

Posted on Sep 28, 2009

  • 17 Answers

SOURCE: My suzuki intruder is missing backfiring on the

Did you sync the two carbs? If not the rear may be getting all the gas from the rear carb and none to the front. Twist throttle engine off and see if front carb cable is pulling the carb open.
Also unscrew the spark plug boot from the front spark plug wire and trim 1/8th inch off the wire and screw the boot back in. The plug wire end may be corroded on that wire.

Posted on Feb 08, 2010

  • 21 Answers

SOURCE: I have a 1995 suzuki intruder 1400, I'm looking

behind the cover on top of the cylinder, Right side for the front, Left for the rear

Posted on Aug 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Battery died and blew both fuel and ignition fuses, replaced them both and put in another battery , soon as connect battery the fuel fuse keeps blowing,, Suzuki Boulevard


Hi, Mark you have a dead short which is usually the easiest to find. Using a test light connected to the hot side of the blown fuse holder, start probing the wire leaving the fuse holder about an inch away the test light should illuminate, keep probing towards the ignition switch until the test light no longer illuminates you are now very close to the short. For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
Fuse Blowing for Instrument panel 08 FLXH Harley Davidson Forums
Keep blowing Fuse 01 CBR600F4i Honda Motorcycles FireBlades org
gauge cluster fuse keeps blowing
99500 38047 03E pdf

Mar 27, 2016 | Suzuki Motorcycles

1 Answer

Fuse keeps blowing


sounds like you have a short in the wiring

are all the signal light bulbs good? if one is out this will cause the blinker to run fast also maybe a bad blinker can

the head light and tail light are on the same fuse check under your rear fender and seat for a naked wire somtimes the tire wares on the wires if they run under the fender also check all running light wires (ie front fender light I had this problem with a FXR and it was the wire under the front fender to my fender light

Jan 24, 2014 | Harley Davidson Motorcycles

1 Answer

Fuse keeps blowing


Hi Anonymous, you have a hard/dead short that should be easy to find generally they are the easiest. Time to get out your test light and start tracking the wire from the power side of the switch, circuit breaker or the blown fuse receiver, when the test light quits lighting you are very close to your short. For a free wiring diagram please visit the website below and good luck.
Harley Davidson Wiring Diagrams and Schematics

Jul 02, 2013 | Harley Davidson XL 1200 C Sportster Custom...

1 Answer

CTSY fuse keeps blowing


ok have your replaced any bulbs? i have found putting bulbs in wrong or just being a bad light bulb can blow fuses. try replacing all bulbs with new ones. its cheap and it could be the problem

Mar 18, 2013 | 2008 Chevrolet Silverado 2500HD

1 Answer

Just got a mx 125, turned the key this morning an it kicked over fine after a thew kicks, went back out agen a thew minutes later tryed to start it agen, turned the key no lights came on an i dont think...


Put your battery on a slow charge for about 2 hours or more, clean your terminals, then try it again.
If your battery is a few years old, get a new one. if still no light check your main fuse it will be located close to your battery, replace if needed. Good luck and if you still need help , submit new
post ok.

Nov 20, 2010 | Aprilia MX 125 Motorcycles

1 Answer

Tail light fuse blowing


If it has a towing package harness,it might be in it.Remove all the tail light bulbs,and put a new fuse in to see if the fuse will blow.If it does,check the head light switch ,and the dimmer for the dash lights for a short.If the fuse does not blow,with all the bulbs out then look for a bad light socket shoring ,out,by putting one bulb in at a time,and when the fuse blows,that will be the socket that is bad.

Nov 11, 2009 | 1992 Toyota Pickup

1 Answer

Taillights and license plate lights not working


there is a short somewhere.put a test light in place of the fuse.
the light will glow bright.when the short is removed,the light will go dim

Jul 18, 2009 | 1997 Nissan Pathfinder

1 Answer

Fuse that operates window, a/c , meters blows when driving


try and take not when it blows to what is on a/c or blows when using windows or straight away
can put head light globe into fuse location head light lights up bright when short is present so you can then locate problem

May 28, 2009 | 1994 Toyota Camry

1 Answer

No parking lights, fuse keeps blowing.


There is a ground not connected or a wire open that is causing it to blow

Mar 08, 2009 | 1999 Pontiac Montana

Not finding what you are looking for?
1991 Suzuki VS 1400 Intruder Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...