Question about Motorcycles

1 Answer

Adjust clutch on 1998 timberwolf - Motorcycles

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

On the right side of engine (just above the foot peg), you should see a nut threaded over a slotted bolt. You should see the words "increase" & "decrease" with arrows pointing in either direction. Loosen the nut around the bolt and turn the screw slightly maybe a 1/4 turn. (turn towards the increase direction to make the clutch engage sooner, turn towards the decrease direction to adjust the clutch to disengage sooner). Tighten the nut, and test your change. You will have to "play" with the adjustment until you get the clutch the way you want it.

Posted on Feb 24, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Yamaha Timberwolf 250 will not turn over. Took it to someone they said it was stator. Replaced stator and spark plug still wont turn. There's no noise anywhere.


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
1994 Yamaha Timberwolf 4x4 Electric Start Problems
no fire 96 timberwolf
http://www.mikekekich.com/92-98%20Timberwolf%202WD%20Service%20Manual.pdf
OEM parts for Yamaha
Yamaha YFB250K Timberwolf Owner Manual

Jan 13, 2017 | Yamaha Motorcycles

1 Answer

Yamaha Timberwolf. How can I find model number to order parts


If you can tell me your vin - or your year I can tell you what model you have. But - if you go onto any parts site - such as cheapcycle.com or partsmonster - you name it - you won't need your 'model' # - just your year. You'd click - Yamaha OEM Parts, then ATV then Year - 1992 - 1998 was the Timberwolf - a lot of parts from the 99 - 04 Bear Tracker will work (just about only changed the plastics and carb in 99 - 04) same engine/transmission/rear end, etc. the brakes also went from drum to disc - but you'd click on the year - and then look - the timberwolf will be right there the 1992 - 1998 Yamaha Timberwolf 250 - I can't remember if they offered a timberwolf 350. If you can tell me the vin or year - like I said - I'll reply with your exact model # - but you can buy and order most parts just by model name and year 95 Timberwolf.

Dec 29, 2015 | ATVs

1 Answer

'92 yamaha timberwolf valve adjustment


Here's the info you're looking for.

1992-1998 Yamaha Timberwolf 2WD and 4WD
Intake: 0.05 - 0.09 mm (0.002 ~ 0.004 in)
Exhaust: 0.11 - 0.15 mm (0.004 ~ 0.006 in)

Jun 20, 2014 | RTO 200cc Full Size Four Wheeler ATV

1 Answer

I need to adjust my clutch on a 1998 ford zx2


Your vehicle has a hydraulic clutch, and there really is no "adjustment." Verify fluid level in the clutch fluid reservoir, and consider replacing clutch plates if you are experiencing slipping.

Apr 26, 2012 | 1998 Ford Escort

1 Answer

1998 Saturn SC1 manuel stick is hard to shift into 1st & 2nd gear


Try to double clutch the clutch pedal. How to double clutch; push the clutch in moving the stick to neutral, then release the clutch and then push it back in and shift into first or second gear. If it works then it is not the shift linkage and could be a clutch adjustment. First how far do you have to release the clutch pedal until the clutch plate starts to engage? If only an inch or so the clutch pedal needs to be adjusted, which is an easy fix (this is more common). The other possible problems could be the clutch plate, throwout bearing of syncros could be bad. If it is one of the previous problems double clutching should buy you some time.

Jul 01, 2010 | 1998 Saturn SC

1 Answer

I have a 1998 volkswagen cabrio and I cannot seem to get the clutch cable to fit it is to much play in it and the clutch is to the ground.


If its a cable then it needs adjustment, then you can adjust the cable on the transmission; however if its hydralic, then the clutch slave cylinder needs replacing.

Feb 03, 2010 | 1998 Volkswagen Cabrio

1 Answer

How do you adjust a clutch on a 1998 suzuki sidekick sport. It has a hydraulic clutch.


A lot of fluid clutches cannot be adjusted. Any that can be adjusted is with slave cylinder The small round bar from the slave cylinder to the plate from the bell housing which holds the trust bearing. Check it you will easily see the adjuster on it if it has one. If your clutch is'nt badly worn and it cannot be adjusted then try bleeding the slave cylinder it may be air. If it is hard to put into gear and the car moves off when you lift your foot up 2 to 3 inches then it needs adjusting if not then the clutch is worn and adjustment won't help. Cheer's

Sep 26, 2009 | 1998 Suzuki Sidekick

1 Answer

Clutch rattle


this sounds like an adjustment issue. you did not mention the mileage...The clutch is released by a bearing, this release bearing needs to come back off of the fingers of the clutch pressure place, early wear and noise happens.

Near the end of the clutch life, you may find that you cannot release any more, if your model is adjustable.

Start with proper clutch release adjustment.

Doc

Sep 14, 2009 | 1998 Volkswagen Golf

1 Answer

Self ADjusting Clutch Cable


Your car uses a hydraulic clutch, they are self adjusting and there is no way to adjust them provided, when the pedal engages near the top of its travel this means the clutch disk is worn out.

May 01, 2009 | 1998 Volkswagen Jetta

2 Answers

I need the timing spec for a 1994 yamaha timberwolf 250


no dont worry about that # what type of machine is it? what your gonna need to do is find the mark on the fly wheel some have a single mark and some have two if you have the cover off put it on there should be 2 access holes take the covers (small and larger probally flat head allen key) turn the engine counter clockwise till you line the second mark you see in that little window if it has two there should be a mark to line it up with, that is top dead center now there will be marks on the cam sprocket thatneed to get lined up also thats where i need to know what kind of machine it is but somehave an arrow some have two lines that get lined up with the gasket surface. if you post it i can help you finish

Dec 19, 2008 | 1990 Yamaha TZR 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...