Question about 2001 Suzuki GSF 600 S Bandit

1 Answer

I am looking for the torque setting for the valve cover any help appreciated

I dont think the haynes manual settings are right

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

The head cover bolts should be 14 Nm or 10 ft-lb...
The head cover union bolts should be tightened first( they're the four centre bolts next to the spark plug tunnels) to 16 Nm or 11.5 ft-lb.
These figures are from the Suzuki service manual...

Posted on Nov 29, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 66 Answers

SOURCE: what is the torque settings for the genorator

10 Nm or ~ = 7 ft-lb

Posted on Aug 13, 2009

Testimonial: "many thanks"

luckyluke78
  • 333 Answers

SOURCE: torque settings for crankcase suzuki bandit 600gsf

Crankcase bolt (M8)
(initial):13 N-m (1.3 kgf-m, 9.5 lb-ft)
(Final):23 N-m (2.3 kg-fm, 16.5 lb-ft)

Please leave positive feedback if you feel I have helped.

Thank you

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cylinderhaed torque settings


The torque settings vary from engine to engine and as I write you have not indicated the engine type you have and from which vehicle make and model.

So no one can tell you the correct settings. But go to the online haynes manual and that will probably give you the numbers you need if they cover your engine.

Mar 20, 2016 | Cars & Trucks

1 Answer

What is the torque pattern on a 2005 valve cover


According to PTCruiser Links.com: " I have a Hayne's Manual that's for 2001 through 2003. It says to tighten all the valeve cover bolts to 40 inch pounds, initially. Then--when all are at that setting, tighten all of them to 80 inch pounds. Then when all are that tight, do the final tightening to 105 inch pounds. Sounds like a weird way to do it, but I bet it won't leak if you follow these directions ....

Before doing this, apply a "light" coating of RTV sealant onto the corners of number 1 and number 6 camshaft bearing caps (I guess some oil will leak if this isn't done). In other words, the back corners as you're facing the engine from the front of the car.

Tightening sequence: Do all the middle ones first, starting with the bolt in the middle of the valve cover, then the one just above it, then the one just below it. Then do the same sequence for the left three bolts. Then do the same sequence for the right three bolts.

Then get a Hayne's manual, because it may not be perfect, but it shows a lot of torque settings and other stuff you will need in the future.

I don't wrench all that often anymore, so I use a torque wrench. My bad!

Tim "

May 10, 2015 | 2005 Chrysler PT Cruiser

1 Answer

318i timing marks dont have the timing toool need the points of the chain on the cams for 318i


If your gears do not have marks you can pull the # 1 sparkplug, insert a wooden dowel rod, rotate the engine until the piston is TDC.
remove the valve cover on the 1,3,5,7 side and adjust the cam as needed to fully closed valves(compression)

Jul 04, 2014 | Repair Manual for 1992-1998 BMW 3 Series

2 Answers

Big ends and mains torque settings for opel corsa


dont think the diesel is covered

only online site i found anthing about these opels
Vauxhall Workshop Manuals

Aug 05, 2013 | Cars & Trucks

1 Answer

I have a gsf 600s bandit and i am looking for the torque settings for the valve cover


The head cover bolts should be 14 Nm or 10 ft-lb...
The head cover union bolts should be tightened first( they're the four centre bolts next to the spark plug tunnels) to 16 Nm or 11.5 ft-lb.
These figures are from the Suzuki service manual...

Nov 28, 2012 | Suzuki Motorcycles

3 Answers

How do you replace the head gasket


with great difficultry, It is verry time consuming end verry costly to have it (Replaced)

Nov 27, 2012 | 2000 Kia Sportage

1 Answer

Torque specs for valve cover


Hi,
Create an account on Autozone's website, add your car, and find the Repair Manual for your car - it should be listed. Or get a Hayne's Repair manual. It should have the #'s too.


Td

Oct 01, 2012 | 1993 Honda Accord

1 Answer

2000 W reg ford escort wheel nut torque settings


2.0L DOHC Engine 85-105 Ft Lbs EX 2.0L DOHC Engine 65-87 Ft Lbs

Please let me know if this information is helpful. Positive feedback is appreciated. Thank You!

Mar 28, 2009 | 1989 Ford Escort

1 Answer

Torque setting


The sprocket nut torque setting is 132Nm. If you are after the plastic cover torque settings, i dont think they have one. Hope this helps.

Mar 28, 2009 | 2007 Triumph Tiger

Not finding what you are looking for?
2001 Suzuki GSF 600 S Bandit Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...