Question about 2010 Honda SH125i
Have a 2009 Honda Scoopy 125. I just changed the battery because the bike would not start. I turn on the key and everything works as should. The problem is when I hit the starter button nothing, not even a sound Press starter switch nothing happens have checked fuse and tried touching the wires from starter switch together still nothing how do I find if it's the relay or the solenoid
Posted by Anonymous on
Hi, Anonymous before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
My Honda Won Turn Over Is Not Starting
Honda SH125 Owner Manual
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Sep 25, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Sort of sounds like a Twilight Zone kind of problem doesn't it. I would have the battery checked for an internal dead short. This is something that happens on odd occasions and can happen even to a new battery. Yea, the little lights will work ( they do not draw much juice ), but the starter motor draws a lot of juice and a shorted battery just ain't got it. Also check the wiring harness connections. One loose connection can cause bunches of trouble.
Posted on Mar 14, 2009
If you can hear the starter run, but no motor turning, the starter clutch is going bad. It is what allows the motor to turn over with the starter, and it idles while the bike is running.
Posted on Jun 09, 2009
Take the starter button off and put a 12 volt tester on one of the 4 leads that are wired into the button. Test each- If you find a hot line, take a small piece of wire and jump the current over to the other parrallel button. I worked on my bike for two weeks before I discovered this problem. Another problem was that the headlight would not come on. The starter would not crank at all. I took a screw driver and raised the brass leads on the switch so they would make contact and put the switch back together, and it worked. Good luck.
Posted on Jul 31, 2009
SOURCE: Have 2003 Honda Sabre. All
Chances are that that problem is not fuse related. It is more likely you have a defective starter button. The starter button does two things. First, it turns off the headlight and , second, it activates the starter solenoid. If
your starter solenoid clicks when you push the starter button, the
starter button is good. If nothing happens when you press the starter button it may be dirty or broken. Try taking the switch apart and cleaning the button contacts.
Next go to the starter solenoid and try jumping the power from one solenoid post to the other. You can use a jumper cable clamp, a screw driver, or touch the two cables together, this sends power directly to the starter. If the starter works now you have a bad solenoid (burnt internal contact points).
If you hold the starter button and tap on the starter with a plastic hammer or back of a screw driver and the starter works , you need new starter brushes. There are no other parts (other than brushes) available for the starter from Honda. If the bearings are bad or the armature is shorted you will have to replace the starter assembly.
Posted on Mar 17, 2011
Tips for a great answer:
Feb 16, 2018 | 2007 Honda SH125i
Apr 15, 2016 | Honda Motorcycles
Jan 05, 2016 | 2009 Honda SH125i
Oct 09, 2014 | 2010 Vuka XL 125
May 12, 2014 | Honda Motorcycles
Mar 14, 2013 | 2009 Honda SWing 125
Feb 16, 2013 | 2011 Honda SH125i
Apr 25, 2012 | 2010 Honda SH125i
Sep 12, 2011 | 2009 Honda SH125i
Mar 18, 2010 | 2007 Honda SH125i
230 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: