Question about 1974 Yamaha DT 360

1 Answer

Im replacing my fork seals and wondered if I can fill the fork leg before I install the seals or must it be filled from the top???

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

Must be filled from the top...plus it would leak out when you change the seals...

Posted on Nov 28, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keep having leaking fork seals.have replaced seals and oil after every ride lately.(4)have tried two brands of seals last time disasembled whole of forks cleaned every part,shims everything and had...


G'day. A couple of suggestions-
Damage to the fork slider-chips or dings.
Too much oil in the fork on re-assembly can cause the seal to go.
Worn or loose fork bushes will flog the seal prematurely.
When you transport the bike-if you don't use a seal saver can pop the seals.

So let me help with these.

Be sure that the fork slider is not scored,dinged or damaged on th surface.

A good double check of the oil quantity is to ensure that when you have re-filled the tube with oil & primed it(worked the air out of it), the oil level should be 100 to 110 mm from the top of the leg to the oil with the fork fully compressed. If the level is less than this-drop it to 100mm.

To check the fork bushes-try pull on the front forks front to back(wobble) & feel for looseness in the bushes.

And finally-When you transport the bike-put a chock(I use an empty 5ltr oil container-but you can buy propper chocks from the bike shop) in-between the forks at top of the front wheel .
Now when you pull the front end down it will stop on the chock & stop the front forks being under excessive compression for extended periods-so it saves the fork springs from sacking out too.
I hope this proves helpfull.
Kind regards Andrew Porrelli

May 20, 2011 | Sherco 5.1i Motorcycles

2 Answers

How easy is it to replace my fork seals on my 1993/4 900 trophy?


I found it easier to remove the forks and take them to a shop to have the seals done.In doing this you are still saving a bucket load of money. Removal of the forks takes about an hour and a half and is relatively easy without any specialist tools. You only have to remove the top part of the fairing.

May 10, 2011 | 1994 Triumph Trophy 900

1 Answer

How to change fork oil on bike


The best and easyest way to do this would be to remove the fork assembly as a unit, remove the top nut invert the fork over a clean container, and allow the oil to drain completely, this may take some time but it less costly than removing the leg and replacing the seals etc, the oil type is 10w40 and each leg is filled to 137 mm below top of fork, with spring inserted but tube depresed, hope this helps

Feb 27, 2011 | 2000 Suzuki VL 1500 Intruder LC

1 Answer

My front fork seals need replacing on my 2005 model TE450, i don't know the specifications, and exactly how much oil to use in each fork


forks need to be removed,and disasemble,and cleaned,new fork seals,reasembleb fit new seals, refit damping cartridge,fill fork with 5w fork oil upto 120mm from top,refit spring, refit fork cap

Aug 14, 2010 | Husqvarna TE 450 Motorcycles

1 Answer

How do I change the fork oil on a 2002 Heritage Soft tail Harley?


look at the fork legs at the bottom there is a bolt on both legs its only a small bolt,,, undo this bolt and the fork oil will drain out,, to refill the forks take the top nut off the fork leg near the handel bars,,,,,,dont over fill with oil,,,and only use the proper oil,,or the seals will blow out and the forks will be very stiff

Feb 06, 2010 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

On my 05 kx250,im changing the fork seals-do you have to fill and bleed the cartridge seperately or just fill up the fork leg?


The best way to fill fork oil is to add the specified amount and let the forks sit overnight to allow all entrained air escape. Leave the fill plugs off. Ofter you let the air escape, plug it up install the forks and add air to the desired pressure if has that option.

Jan 18, 2010 | 2005 kawasaki KX 250

2 Answers

How do i fill the front forks of my honda vts1300 after i replace the front fork seals


just pour oil in the top of the fork compressing the forks at the same time notice it will sqweel a lot as this is happening keep pumping the forks till the sqweeling stops fill each leg with 459mls buddy

Oct 12, 2009 | Honda VTX 1300 C Motorcycles

3 Answers

How do I change the fork seals on a 2008 Honda CRF 250 r? Do I use a special tool? Oil? How much oil? Thanks so much for your expertise. Do I put equal amounts of oil on each side? Inner tube- outer tube?


hi,replacing the seal is quite easy,although it will sound complicated,jack up or lift the bike off the ground so that the front wheel is in the air(about 12-14 inches should be enough,remove the front wheel from the bike,remove each fork leg,this is done by undoing the bolts(4 on each leg)the front fork is quite easy to work on just do one at a time,remove the dust cover from the top of the staunchion tube(larger diameter tube),beneath that dust cover you should see a retaining clip that holds the seal in place,remove the retaining clip(and dont lose it),the seal is now ready to remove,the easiest way that i know to do this is to force a screwdriver through the body of the seal,you may need to hit the screwdriver with a hammer as some seal have a tin backing plate,put a hole through the seal on each side of the fork leg taking care not to damage the chrome of the fork leg,then use the screwdriver to lever the seal out of the fork leg,to reinstall the new seal,put a smear of grease or oil around the outside of the new seal,slide the new seal down the fork leg and seat it squarely into the fork tube,very carefully tap the new seal into place being very carefull not to damage the outer surface,i use a small piece of dowell type timber to do this as the wood doesnt damage the seal surface,i use a small ballpeen hammer to tap the wooden dowell,once you have the seal seated down the tube you should be able to see the groove for the retaining clip,reinstall the retaining clip making sure it is seated corectly,replace the dust cover,if you are going to replce the fork oil or top it up do this once the fork leg is back in the bike,repeat the whole procedure for the other fork leg,once you have done the fork seals reinslall the fork legs back into the bike and refit the front wheel,to top up the oil in each leg,simply undo the large cap on the end of the fork leg,you may have to remove the handlebars to do this,be carefull as the cap will be spring loaded and can easily fly off if you are not ready for it,top up or fill with the correct weight oil for your bike(normally a 10w oil),check with your local honda agent for the correct quantity,normally between 400-500 mls,this all sounds quite complicated but is actually quite easy and can be done with a minimal of tools,each fork shold take about 1/2 hr to do...hope this is a help to you

Jul 15, 2009 | 2005 Honda CRF 250 R

1 Answer

How do i dismantle front forks to replace the oil seals


You just needed to.... remove front wheel, support bike on something, undo retaining bolts on forks, tap out fork legs from the top, using a soft mallet. Take out fork seals with a seal pick, (halfords) Replace old seal with new seals, in reverse order) sliding over the fork leg, tapping into place. Then put replace forks etc in reverse order (from dissassembly). Hope this helps

Feb 21, 2009 | 1992 Honda CB 750F2 Seven Fifty

Not finding what you are looking for?
1974 Yamaha DT 360 Logo

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...