Question about 2005 Kymco Grand Dink 250

1 Answer

2006 kymco 250 quad... failed to start this morning for the first time ever,pressed the ignition switch and it was if the battery was dead..then tried it again and there is nothing...no sound,no clicking...nothing!!!! lights are still strong etc..

Posted by on

  • surfjunkie_7 Jan 15, 2009

    was the solenid....thankyou very much..

  • Anonymous Apr 30, 2009

    when i start the machine and drive whatever howlong, as soon as i switch it off, for exemple when i stop somehwere and switch the machine off, and when i try to start it again, nothing will happen, even on the board there will be no lights at all, but when i wait 2 hours till 3 h, everything is here again, when i switch on, on the board lights are on, and i can start the machine normally and i can drive howlong i want, till i twitch off, and the operation starts again, i can do nothing just after the 2 .3 hours are passed. what can this be ? could you please help me, knowing that i am begginger with the Quad, Kymco 250 sport. thanks in advance.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 48 Answers

Try tapping on the starter it may be in a bind if it still does nothing then change the solenoid

Posted on Jan 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My kymco 250 EGO just dies at the top end which is dangerous.Could it be the carb? IF SO IS THERE A MANUAL I CAN DOWNLOAD TO HELP ME TAKE IT APART? Thankyou geoff


Hi, Geoffrey and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Accelerator pump damaged or not working.
11. Water or dirt in the fuel system, carburetor or filter.
12. Restricted, blocked or kinked fuel line.
13. Fuel tank empty.
14. The gas cap is not venting properly or fuel tank venting system blocked.
15. A failed fuel pump, pressure regulator and or fuel injectors.
16. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
17. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have a nice day.
My scooter shut off while driving any ideas what it could be scooters
Scooter keeps cutting off while driving SCOOTER PROFESSOR
View topic Scooter just turned off while driving
http://www.scootermasters.com/manuals/People-250-Full-Manual.pdf
http://www.kymcousa.com/owners/onroad/Venox250.pdf

Aug 28, 2016 | Kymco Motorcycles

1 Answer

Kymco S Peoples200, engine starts but fades very quickly


Hi, Dave the following applies to carbureted also fuel injected models and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Accelerator pump damaged or not working.
11. Water or dirt in the fuel system, carburetor or filter.
12. Restricted, blocked or kinked fuel line.
13. Fuel tank empty.
14. The gas cap is not venting properly or fuel tank venting system blocked.
15. A failed fuel pump, pressure regulator and or fuel injectors.
16. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
17. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have a nice day.
s200 stalls after 5 10 minutes
GY6 stalls immediately after starting
problems with my Kymco 200 People
http://www.49ccscoot.com/manuals/Kymco_People_S_50-200_Service_Manual.pdf

Jun 15, 2016 | 2010 Kymco People S 200

1 Answer

2006 Venox 250. Why won't it start?


Hi,try undoing the battery and leave for 30mins and reconnecting the battery and see if it rights itself,worth a try.

Jul 16, 2015 | Kymco Motorcycles

1 Answer

Kymco mongoose 250 won't start


Remove battery terminals and clean both posts and terminals
with sandpaper until you see shiny metal. The black coating is lead sulphate which has a high resistance to current flow both into and out of the battery. Have a load test done on the battery also as a cell may have dies while you were riding and the bike was running on the alternator.

Jul 18, 2013 | Motorcycles

1 Answer

I have a kymco agility 50 and it won't start. It has no power what so ever, the starter won't turn over and the break light won't light when I pull the break. I checked the kill switch.


Check with a multi tester for voltage coming through the ignition switch lead wires + to switch wire - to ground you shoul get 12volt or higher, with the switch off you should have one live (feed from battery ), on you should have 2 or 3 in and out feed (possibly 2 out one for ignition one for light curuit), or disconnect the switch and check for continuity (12v battery wire and a bulb if you dont have a multi tester between each pin on the switch plug when turned on you should get a curcuit when on.

Jan 27, 2012 | 2006 Kymco Agility 50

1 Answer

No spark on my venox 250?


Possible failure of the ignition unit. you need to trace the voltage to the coil, the trigger voltage if absent then the ignition system is defective. Check the input and also the 12 volt to the coil , if coil is heating it can be faulty.

Nov 30, 2011 | 2003 Kymco Venox 250

1 Answer

My kymco xciting 250 wont start. i have not ridden it over the winter. i have gassed it up and charged the battery. when i hit the starter the lights blink on the panel but it will not turnover.


Did you warm up your Kymco during winter? If not then your first priority is to have your battery professionaly measured for cranking power capacity or get a new one..

Mar 15, 2010 | 2005 Kymco Xciting 250

1 Answer

2005 Kymco 250cc quad 4 stroke, all auto. Won't start


get a can of starter fluid and spray a short burst into the air intake...it should fire up...if it won't stay running or idle your carb is clogged from storage i presume...right? usually storage for more than 3 mos will clog a carb if you did not winterize it...Good luck to you friend...Tim

May 11, 2009 | 2005 Kymco Grand Dink 250

Not finding what you are looking for?
2005 Kymco Grand Dink 250 Logo

401 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4473 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...