Question about 2007 Boss Hoss BHC-3 ZZ4

1 Answer

Reverse fuse blows. Is their a common cause for this?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 65 Answers

Hello

I am assuming that this is an ELECTRICAL issue for the above problem so I will answer electrically as it wasn't 100% clear.

Its because somwhere down the line you SHORT-CIRCUITED the 2 wires going to the reverse light of your motor bike. If it is just ONE wire going from the reverse fuse to the reverse light then the main problem must be that the wire's insulation somewhere is going to earth (metal chassis of your bike) before it actually reaches the bulb hence it blows your fuse. First try by removing the bulb and see if it still blows without the bulb in place. Then this means that you will just have to check from the bulb holder to the fuse for any cuts in the wire etc. Your problem is a short-circuit.

Hope that this helps :) I love bikes :)

Best Regards

Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car blows engine fuse when put in reverse


It would seem there is a fault on the reverse light circuit causing the fuse to blow, though I am surprised it is blowing the engine fuse, perhaps it is an auto transmission with electronic management?

Manual or auto? Given the fault it is probably auto so I expect the reverse light is unaffected and so too the gear selector inhibitor switch operation? If this is so it would suggest a fault with the transmission, the electrical connections, wiring or electronics.

Sorry I can suggest no more given your rather sparse description.

Jul 01, 2016 | 2003 Ford Escort

1 Answer

Reverse light fuse is continually blowing 1999 mitsubishi galant


The speed sensor is probably the root of your problems. Likely the reverse switch wiring is routed through the harness for the sensor. That could also be the reason it goes into limp mode. Change the sensor and see if all problems are resolved. Good luck.

Jul 24, 2013 | 1999 Mitsubishi Galant

1 Answer

2004 Lexus keeps blowing ECU-B fuse


A bad outside mirror motor will also cause that fuse to blow. Is your fuse blowing when you adjust the mirrors or when you put the car in reverse? If yes, then the mirror motor is the problem.

Aug 18, 2012 | Lexus GX 470 Cars & Trucks

1 Answer

My fuses keep blowing in my 2000 sunfire, my dash lights went out and when i replaced the fuse my reverse lights stay on, so i removed the fuse and now my tail lights dont come on,


those have common problems with the cluster panel but before you replace it check under dash for the light that lights up your feet when you enter vehicle they are easily broke and can cause shorts

Feb 18, 2010 | 2000 Pontiac Sunfire

1 Answer

Reverse light fuse blows when put into reverse


Unfortunately, many possibilities. If you have time, start by removing both reverse lamp sockets from light assembly(and keep from touching any metal), remove bulbs from sockets, CAREFULLY INSPECT sockets and wires. New fuse of correct rating. Turn key on and try again in reverse.
Fuse still blows: Next place to look is transmission reverse electrical switch and wiring as far as you can trace looking for burned/stripped wires near transmission and wires by sockets
Fuse doesn't blow: Turn key off and install one lamp in socket at a time. DO NOT install sockets into fixture at this time. Test. Remove first lamp to check second. If still O.K., each socket back into fixture(one at a time same as before)and test. Most common problems: Sockets contaminated, wires shorting at sockets, bulbs installed incorrectly shorting to ground.

Sep 25, 2009 | 1996 Ford Explorer

3 Answers

Reverse lights fuse blew


hi
check the wire because if the fuse keep blowing there's a wire somewhere on the car that has contact with the frame so everytime you put your car on reverse the 12V wire shortcut on the frame so the fuse blow check all your positive wire and your bulb as well
Good luck

Jun 19, 2009 | 1997 Ford Explorer AWD

1 Answer

Reverse causes fuse for instrumental cluster to blow


Yes there is a reverse light back up switch located on the side of the transmission it will be the only 2 wires going to the tranny. There might be a short in the switch itself or the power wire to switch might have a bare spot where it might be grounding out on the vehicle somewhere.

Jan 19, 2009 | 1992 Toyota 4Runner

1 Answer

Reverse fuse blows when reverse button is pressed.


Hello

I answered in your other post as well. I am assuming that this is an ELECTRICAL issue for the above problem so I will answer electrically as it wasn't 100% clear.

Its because somwhere down the line you SHORT-CIRCUITED the 2 wires going to the reverse light of your motor bike. If it is just ONE wire going from the reverse fuse to the reverse light then the main problem must be that the wire's insulation somewhere is going to earth (metal chassis of your bike) before it actually reaches the bulb hence it blows your fuse. First try by removing the bulb and see if it still blows without the bulb in place. Then this means that you will just have to check from the bulb holder to the fuse for any cuts in the wire etc. Your problem is a short-circuit.

Hope that this helps :) I love bikes :)

Best Regards

Jan 07, 2009 | 2007 Boss Hoss BHC-3 ZZ4

2 Answers

Fues blown in xpower inverter 1750 plus


These fuse are often intend to protect voltage inversion. (reverse voltage)
So, if the eight fuse are blown, then maybe the voltage red and black wire were not connected to the correct polarity.

then again, even if these fuse are intend to be use as reverse protection, it may occure that transformer short out, transistor short out and many other short circuit inside the inverter as occure.

So replacing all eight fuse might not restore the unit function, they may even blow again.
Also, reversing polarity that cause the fuse to blow might have damage the transistor stage.

I am still, investigating few other problem with those unit.
I don't have all answer yet.

regards,

Hitheck

Dec 21, 2008 | Xantrex Technology Xantrex Xpower 1750...

1 Answer

B;owing fuses, wont power up, just smokes


Hi,

Try checking the reverse protection diode. This diode would normally be connected right after the power connector and would be the biggest diode inside. One way to verify if this is defective and causing the fuse to blow is even with the power switch at the OFF position, the fuse will still blow.

If on the other hand, the reverse protection diode is good and fuse will not blow when power switch is at OFF, then the short/defective component is inside. There would only be two (2) major components that can cause the fuse to blow with the power switch to ON, the final transistor and/or the audio IC.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jun 06, 2008 | Cobra 29 LTD CB Radio

Not finding what you are looking for?
2007 Boss Hoss BHC-3 ZZ4 Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boss Hoss Experts

yadayada
yadayada

Level 3 Expert

69244 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

13679 Answers

Mike

Level 3 Expert

4332 Answers

Are you a Boss Hoss Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...