Question about kawasaki Motorcycles

Open Question

How to remove the driver seat on a 04 zx10r - kawasaki Motorcycles

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 36 Answers

SOURCE: Engine swap 04 zx10r on a 06 zx 636 f

The zx-10r engine is too wide to fit inside the 636 frame. Probably too much work to fit it but it would be awesome to have a zx-10r disguised as a 636.

Posted on Jun 09, 2012

Ad
  • 1 Answer

SOURCE: Engine swap 04 zx10r on a 06 zx 636 f

No. But 636 decals will fit on a zx-10r.
Be surprised how many believe what the decals say.


04 zx-10r
78mm Wiseco
Web cams : Lift: 384/358 Duration: 272/268 Duration@ 0.050": 248/241
Head a little warmed. Springs etc.
Akropavic full titanium
520
636 graphics
A few "Go Fast" parts for looks

Pros: Run down most anything on the street
Cons: Have to use 110 rated fuel

Posted on Mar 14, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove seat to change the battery please?


if it is a zx10r 05 model there is a rear plastic cover that is directly behind the rear passengers seat which also wraps around both sides of the bike to meet both side covers ,on the left hand side of the rear cover there is a key barrel that unlocks the rear seat ,but the key is barrel hidden and can only be seen by looking underneath and the key is inserted with the main plastic (black handle)bit facing toward the ground and the metal part of the key will be pointing towards the sky ,so you will have to sit on the ground to see it and look or feel under to find it and when you do it will remove rear seat so when you turn the key lift up on the front of the rear seat to remove it then you will see that the front seat is held down by a bolt .

Apr 20, 2015 | kawasaki ZX-10R Motorcycles

1 Answer

I have a 2007 Kawasaki zx10r and there is fuel running out of the overflow hose


if it has carbie/s then check for a faulty float needle and seat
may be a simple thing such as a hair stuck under the needle as it is flooding

Apr 06, 2013 | 2007 kawasaki Ninja ZX10R

1 Answer

I have a Kawasaki zx10r i replaced battery and after riding bike for few minutes u loose all power to bike lights and tach lights on console than have to jump bike to get it to start than it will do again


I bought a 04 zx10r. good battery but no electrical power any where but the starter relay. all of the suspected componets were chect on a running bike and perfermed normal. the issue was in the wire harness. I found a short in the #1 terminal connector on the left rail of the seat frame. It is hard to find as it is wraped in black tape. I found that the wire terminal had corroded and broken into. This wire leads back to the positive side of the starter relay and from that point it powers almost everything on the bike. I hope this helps. Good luck. Gixxerboy.

Jun 23, 2012 | 2007 kawasaki Ninja ZX10R

1 Answer

How do i remove the drivers seat on a 2008 zx10


Remove the two small panels under the seat. Then remove the screw in center holding seat in place.

Apr 16, 2012 | 2008 kawasaki Ninja ZX10R

2 Answers

Would after market slip on exhaust affect engine compression of zx10r? What is the best after market exhaust slip oni can to use that would have no effect at all on the power of the zx10r? Are there any...


As long as you get a muffler that is comparable to a stock muffler then it will have no effect on the performance. Most aftermarket companies make stock mufflers that would fit your bike though it would likely be cheaper to just replace them with stock kawasaki pipes.
As to replacing them, using an impact wrench will make removal easier and be sure to use a new clamp even if the old one looks good

Oct 04, 2011 | 2009 kawasaki Ninja ZX10R

1 Answer

Can I get the procedure to remove the power drivers seat in my 04 Malibu?


Seat is held to the floor with four bolts. Remove them and disconnect wiring harness.

Aug 06, 2009 | 2004 Chevrolet Malibu Maxx

1 Answer

Where are the three vin numbers on a 04 zx10r


there is a motor number on the cases and there should be a number on the steering neck but a third number i dont know

Jun 22, 2009 | kawasaki ZX 10 Motorcycles

3 Answers

Engine swap 04 zx10r on a 06 zx 636 f


The frame mounting points are completely different. A zx 636 frame wraps around the motor where as a zx10r frame goes directly over the motor. That's how they keep the zx10r nimble enough to feel like a 600cc sport bike. But in this day and age if you have enough time and money you can accomplish anything. Honestly it's just easier to sell your 6 and buy a 1 liter.

May 31, 2009 | 2006 kawasaki ZZR 600

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...