Question about 2009 Harley Davidson VRSCF VRod Muscle

1 Answer

Replaceing battery now my lights stay on with the ignition off

When i was replacing the battery on my 2009 V rod muscle i made sure i hooked up the positive side first. then as i started to hook up the negitive side my speedo lit up. and i was like what is the bike ignition switch on. i looked down and its in the off position. so now what

Posted by Anonymous on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have cleaned the ground under the seat and the negitive battery and where the negitive batter hooks up to the stud on the Engine block. I have checked all fuses front right panel, and main fuse and rear fuse box under the seat ALL GOOD! Still i have the same problem so I guess i need to take of my Speedo and Discon and Reconnect.

Posted on Nov 05, 2012


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 2336 Answers

SOURCE: No power when I try to start bike, just a click…

Check the battery connections. Remove, clean and reinstall them. You probably had them off doing the wiring and they aren't making a good connection now. Always remove the negative first and install it last.

Posted on Nov 20, 2008

  • 706 Answers

SOURCE: Should my 2002 flstci run if positive connection is disconnected

Hello edmunds_don,
The battery is there to supply starting power only and your bike should continue to run if it is started and you remove the positive terminal. You need to check your voltage regulator to make sure it is getting more than 14V to it while the motor is running. If you provide an email address, I can send you a pdf version of a service manual for a 2003 Heritage ( that is what I have) but the charging system should be pretty much the same. You can email me at with your contact information. I assume you checked all the fuses first... If not.. check all the fuses first...
( use a continuity meter and not just by eye) Also: if you do want me to send you that information..make sure you put something related to that in the subject line of your e mail ..or I might think its spam..

Posted on Dec 08, 2008

  • 469 Answers

SOURCE: 2006 Screamin Eagle Fat Boy- tach, speedo, blinkers not working

You've blown a fuse, check the fuse block. it should be an accessory fuse.

Posted on Apr 13, 2009

  • 420 Answers

SOURCE: Replaced positive battery cable + spark=bike will not fire up

I am afraid to make assumptions as to what else you have checked due to some negative feedback. Did you LOAD check the Battery? Did you check and clean your grounds? If you have done all of that the next logical problem is the solenoid, which can be rebuilt.

Posted on Apr 25, 2009

  • 2 Answers

SOURCE: 2009 FLSTC... a locksmith broke off a key in the

I assume that the 09 is the same as my 07.Remove the single nut cap in middle of dash console.(1/2 inch wrench)The console will lift off and the ignition switch is held on with four(?) screws.Unplug connector,plug in new and reassemble.

Posted on Oct 02, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you remove a 2009 hyundai accent ignition

If you are talking Ignition Coil's (shown in the Picture) then it is only held in place by the Connecting Wire and a Single 10mm Bolt. If you are talking removing the Ignition where the Key goes, you have to take the Air Bag off (make sure you disconnect the Battery) and then there is a SET SCREW in the Steering Column that you have to remove

Jul 21, 2014 | 2009 Hyundai Accent Ignition Coil...

1 Answer

Replaced head gaskets on 91 legend and car won't turn over and the battery and check engine light stay on with key off hooked everything up right and torqued back to manufactured specs don't know what...

Are you sure you got the timing correct with both heads and the crank shaft, when you installed the timing belt? If wrong, this can cause a no crank/no start situation. As far as the battery and check engine light staying on when key is off, sounds like ignition switch is malfunctioning, or computer. Why did you replace the head gaskets?

Apr 10, 2014 | Cars & Trucks

1 Answer

2009 VRSCF

Here's a quick take from the official H-D release. The wide, angular air-box cover and chopped tail section look as solid and smooth as billet and give the new V-Rod Muscle lines that are clean and powerful. The size of the massive 240 mm rear tire is accentuated by the new broad, clipped and clean rear fender. The combination stop/tail/turn LED light is tucked under the edge of the rear fender, and the side-mount license plate leaves the fender surface smooth and uncluttered. Front-end styling balances the rear, with a trimmed fender that's blacked out behind satin-finished inverted forks and LED turn signals integrated into the mirror stems. The radiator shrouds are restyled and color-matched to the rest of the bodywork, while the new airbox side covers incorporate air scoop inlets covered with woven wire mesh. The silver five-spoke cast aluminum front and rear wheels are a new design for the V-Rod line.

Jul 26, 2012 | 2009 Harley Davidson VRSCF VRod Muscle

1 Answer

Where can I buy an owners manual for my HD V Rod Muscle 2009? Thanks


You need to sign in or create a profile :

You could access all the manual from their site.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Sep 01, 2011 | 2009 Harley Davidson VRSCF VRod Muscle

1 Answer

How do you get the front bulb assembly out past the lower bumper to replace bulbs ? 2009 Tahoe

each headlight has a rod L shaped on the right and left end of the light. they look like latches. unlatch

the rods and pull them straight up. once the rods are removed you can pull out the headlight assembly,

and you can have access to your running lights. on the battery side you may have to remove the battery

putting the lights back on is the reverse process, you just have to alighn the holes and make sure the

wire does not get in the way. good luck!

Feb 14, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

My Goodman GSMS 100-4 won't stay lit. It starts up the HSI glows, gas valve opens ignition, flame and after a few seconds the flame goes out. The light blinks one time (repeating). I replaced the flame...

Hello Flame rod should have done the trick.Make sure the rod & the control are GROUNDED (earth).Make sure the rod is not touching anything & in the gas flame.

Sep 22, 2010 | Goodman Heating & Cooling

2 Answers

Where is the location of the ignition sensor on 2004 kia optima lx 4 cyclinder 4 door sedan

the ignition module is to the left of the air filter, right against the right side of the engine. I replaced mine, just two screws and take off black plastic covering. Make sure u disconnect negative battery post first. When done hook negative back up. If engine light don"t go off for P0320 code, disconnect battery for 5 min and connect back, I let my battery stay disconnect overnight.

Jul 22, 2010 | 2004 Kia Optima

Not finding what you are looking for?
2009 Harley Davidson VRSCF VRod Muscle Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers


Level 3 Expert

4340 Answers


Level 3 Expert

76109 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides