Question about 1993 Suzuki GSX 600 F (Katana)

Open Question

How to put back on all the hoses andand gas take set up please help

I took it of and dont remember where everything goes please help

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is gas leaking out my Evap fresh air hose every time i try to put gas in my car and start it


I suspect you are OVERFILLING your tank...

There should be a direct connection from your canister to the top of the fill tube. It is intended to safely draw out gas fumes.

even if you don't OVERFILL... gasoline can expand (coming from the cold ground... into a nice warm car) enough to repeat the symptoms you have depicted.

Try putting in less gas...

Things will most probably resolve themselves... otherwise you might need a new canister.

Be safe... DO NOT OVERFILL.

Jan 03, 2016 | 1999 Pontiac Grand Am GT

1 Answer

My mcculloch fhh18a pressure washer is leaking at the handle ,I took it a part and replaced the seals on the hose know I don't remember how to put everything back together please help


I've had a look online and can't find any parts lists to give you a guide so my advice is get a neighbour with good DIY skills / local mechanic who can work out what goes where. Most bits will only fit one way. Its embarrassing I know, but look over their shoulder, then you will know next time and breeze through it with your new found knowledge.

Jul 02, 2015 | McCulloch Garden

1 Answer

I have a yard machine 46 inc deck i took the deck off and now i dont remember where the pto engage blades spring goes model number 13rn771h729 yr. 2007


it will be near the rear of all the pulleys probably just above top of pulleys look for a simple hole where it hooks usually a 1 inch piece of stock

May 16, 2014 | Yard Machines MTD Gold 20 HP Lawn Tractor ...

1 Answer

Took apart the washer and dryer and need to put it back together...i have everything except where the clear plastic hose goes


Kristen-follow the hoses-water comes into machine at the water supply valves-hot and cold which go into the tub-then there is a drain pump which is connected to the tub via a hose-the out put of the drain pump is connected to the drain through the back of the machine usually at the bottom and this goes into your houses' drain-follow the hoses and you shall reach laundry success-cheers Denny

Oct 25, 2013 | Frigidaire FEX831CS Top Load Stacked...

1 Answer

How do i change the thermastat in a 1991 ford explorer. i hope i dont need a new radiator??


locate the hose that goes to the top of the radiator that hose leads to the thermostat, remove the hose, at the engine there is a water neck be careful as it is rather old and may have rust and is prone to break, remove the 2 screws that hold it in place, remove the water neck (thermostat housing) and remove the old termostat, scrap the housing and engine block from old gasket and silicone, add silicone to the housing and place thermostat in housing in circular ridge then place the gasket over the thermostat apply more silicon over the gasket and spread evenly, allow the silicone to set for a couple of mins and then put the housing back with the engine then connect the hose back and your all set; remember the thermostat part that goes into the engine should be the part with the spring, hope that helps

Jul 13, 2009 | 1991 Ford Explorer

Not finding what you are looking for?
1993 Suzuki GSX 600 F (Katana) Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...