Question about kawasaki Motorcycles

Open Question

Schematic for 1976 kawasaki kz900 indicator lights

Need schematic for indicator light

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: HAVE A 1976 KZ900 Z1 AND IT ISNT GETTIN ANY GAS

Probably a plugged up filter screen in the gas tank petcock (gas valve). Drain the gas then remove the petcock and clean the wire mesh filter. Your bike is getting old and rust accumulates in the tank. You may want to get a liquid tank liner to lock the rust in place and so the tank won't rust anymore. Install an in-line fuel filter as well. A site for the tank liner is below.

Google kreem fuel tank liner “ or go to www.http://www.4secondsflat.com/Fuel_Tank_Sealer.html

Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the
carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.

Please rate this solution. Thanks!

Posted on Apr 22, 2009

  • 6 Answers

SOURCE: WHERE IS THE IDLING SCREW ON THE CARB FOR A 1976

Usily the iding adjustment screw is in the middle of the the carbies on the bottom side between the carby fuel bowls.

Posted on May 10, 2009

  • 1 Answer

SOURCE: i need wiring schematics for a 2001 kawasaki

Have 2002 Vulcan 1600 Drifter. The tail and brake lights will not work. They were working rear turn signals do. It blew the fuse twice, now it is not blowing the fuse but still no lights. Got power to the fuse and leaving it not arriving at the rear light. The plug in,before it goes inside the rear fender, what color wires are what so I can check if things are arriving there O.K.?

Posted on Oct 07, 2009

  • 302 Answers

SOURCE: I need a wiring diagram for my 175 cc Kawasaki KE

A service manual is a very valuable tool, esp. with a bike of that age. Dealer, mfr. and clymer books are sources for that. Meantime, the public library may have your info in the 646 stacks of reference section.

Not sure about 2nd plug. If its wired, then its to insure you get ignition in the cylinder. Some mfr's did that for a while.

Posted on Oct 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1976 kz900 no compression on kick starter.


Sounds like a broken cam drive chain.
Either that or there is not enough valve clearance. These do need checking as the vales wear and close the gaps.
They should be 0.075mm to 0.125mm range (3-5 thou inch).
You would need to take off the cam cover to check either way.

Feb 17, 2013 | kawasaki Motorcycles

1 Answer

Hi i have a really old Kawasaki ke 100cc that i fixed up. but is is too damaged to have the lights and indicators. i want to know how to wire the bike up with just the (magneto) cords from the engine to...


no headlight and no start. the starter switch is bad. the switched needs to be removed and cleaned and also the guides for the shunt need to be fixed. the overheating of the switch melts the plastic guides and prevents the shunt from sliding up and down. it sticks in the down position and stops the headlight ans starter from working. when you get the switch working again you should put your headlight on a relay to remove the power draw through the switch. Kawasaki ke 100cc wiring schematic Google Search

Sep 02, 2017 | 19791994 KAWASAKI KE100 KE 100 Factory...

1 Answer

Wiring schematic,1976 Chevrolet Blazer Electric Windows and locks schematic.


ok i have a 1976 k5 blazer and all of the sudden my blinkers stopped working.The hazzards work but when i hit the brakes alll of my lights stop blinking and stay solid.I checked my fuses but all is well can anyone help me? Its my daily driver and i dont want a ticket for something so small so please help open to any info. thankyou

Apr 05, 2010 | 1983 Chevrolet Blazer

1 Answer

I need a wiring diagram for my 175 cc Kawasaki KE 1976 all the indicator wiring pluss lights have been stripped off the bike pluss?? whats the other spark plug in the head for ?


A service manual is a very valuable tool, esp. with a bike of that age. Dealer, mfr. and clymer books are sources for that. Meantime, the public library may have your info in the 646 stacks of reference section.

Not sure about 2nd plug. If its wired, then its to insure you get ignition in the cylinder. Some mfr's did that for a while.

Oct 06, 2009 | 1976 kawasaki KE 125

3 Answers

I need a wiring schematic for a 1976 KZ750


the library has mc books sec 629or get ahold of clymer or haynes manual

Aug 10, 2009 | 1976 kawasaki Z 750

1 Answer

WHERE IS THE IDLING SCREW ON THE CARB FOR A 1976 KZ900 Z1


Usily the iding adjustment screw is in the middle of the the carbies on the bottom side between the carby fuel bowls.

Apr 25, 2009 | 1975 kawasaki Z1B

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...