Question about Harley Davidson Motorcycles

1 Answer

What is the torque spec for front axle on 2012 blackline?

Torque requirement for front wheel install

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,868 Answers

Hi John, here are your axle torque specifications for all late models 2000 and up.
1. Front axle nut 50-55 ft lbs.
2. Front fork slider cap nuts 11-15 ft lbs.
3. Front fork pinch bolt 30-35 ft lbs.
4. Rear axle nut 60-65 ft lbs.
Good luck and have nice day.

Posted on Jun 23, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 74 Answers

SOURCE: Installing front tire on 1993

A good rule of thumb is 14 foot lbs.

Posted on Jan 16, 2009

v2iper
  • 150 Answers

SOURCE: torque specs for 04 electra glide front axle and

55 ft lbs on front 95 to 105 on rear ft lbs...Fork Cap just tighten it down real tight. I never bother to torque them. they have a lock washer. the one to the rear for some reason ALWAYS gets loose and should be checked say every 1000 miles. Never found one that came off they just get looser where as the front one stays tight.

Posted on Aug 23, 2009

wd4ity
  • 4565 Answers

SOURCE: what is the torque spec on the front axle nut on a

50 foot pounds.

Posted on Feb 26, 2010

Testimonial: "Thank you very much, this info is very helpful as I need to remove and install my front tire today and lost my manual. "

  • 63 Answers

SOURCE: rear wheel alignment and axle assemby 95 sporster

H-D rear axle torque is 60-65 foot pounds.

Posted on Aug 09, 2010

SOURCE: Torque spec for front axle bolt, front axle pinch

take 25.00 and buy you a repair manual..its worth it.

Posted on Aug 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque spec for 2006 Buick Lucerne front bub bearing?


2006 Buick Lucerne

The Hub Bearing Torque - Front

If Torque Specs are not in the box we recommend you torque to this setting. Axle Nut: 118 Ft/Lbs.Wheel Studs: 100 Ft/Lbs. WARNING: Failure to observe the following warnings could create a risk of ***** or serious injury.Proper maintenance and handling practices are critical.Always follow installation instructions and maintain proper lubrication.Every reasonable effort has been made to ensure the accuracy of the information contained in this writing, but no liability is accepted for errors,omissions or for any other reason.This information is not intended to substitute for the specific recommendations of your vehicle manufacturer.Always use the recommended torque requirement unless otherwise specified in the carton.Depending on the application, type of hub unit bearing and location, the installation process may vary.Please review the vehicle manufacturer's recommendation before removing or installing components.

Apr 23, 2017 | Buick Cars & Trucks

1 Answer

What are the torque specs for a front wheel bearing?


if its not a drive axle and only has a castle nut with a cotter pin , then regrease the wheel bearings and run nut all the way in to its hand wrench tight (not impact gun), turn wheel one or two full turns to seat it , then back castle nut off two spaces and install cotter pin , this s\is std way to set proper spacing on wheel bearings

if its a drive axle consult your cars model and make and year torque specs book

Mar 29, 2016 | Cars & Trucks

1 Answer

What is the hub nut torque spec for 2011 Dodge Journey?


are you talking about the big 32mm nut that holds the CV axle to the hub?

2012 Wheel Bearing Front Brake Chassis Suspension

as seen on diagram as #1?

it's stated in that forum as 118 ft lbs & great tip at step #6 to get it to the correct torque setting

Mar 31, 2015 | 2011 Dodge Journey

1 Answer

What are the torque specs for a front axle bearing/hub?


Not sure about your model, but in general they are usually around 180 ft./lbs.

Aug 01, 2014 | 2003 Chevrolet Silverado 1500

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

Torque Spec


Front wheel bearing hub is 147 ft lbs. Axle nut is 170 ft lbs.

Oct 06, 2012 | 2006 Hyundai Accent

1 Answer

What are mazda 6 wheel bearing torque specification


What is the front axle torque on a 2004 Mazda 6

Mar 17, 2012 | 2004 Mazda 6

1 Answer

Need specs for changing rear and front tires for 2002 royal star venture including torx specs


I'll include the obvious, since I'm not sure exactly what you need:

Front tire - 150/80-16 Dunlop D404F or Bridgestone G705, recommended inflation 36 p.s.i.

Rear tire - 150/90-15 Dunlop D404 or Bridgestone G702, recommended inflation 36 p.s.i., 41 p.s.i. with passenger or load.

The front tire can be removed (motorcycle on lift) without loosening calipers or any other parts once axle shaft has been withdrawn; after the tire has been changed and the wheel and axle shaft is back in place, torque for the axle nut is 58 ft.-lbs (78 nm) and the pinch nut is 14 ft.-lbs. (19 nm).

The rear tire requires removal of the right saddlebag and brake caliper, as well as the axle shaft. During reassembly, the torque for the axle nut is 110 ft.-lbs. (150 nm), for the pinch nut on the swing arm 17 ft.-lbs (23 nm). Bolts for the caliper should be torqued to 30 ft.-lbs. (40 nm).

It's a good idea to lubricate the drive splines in the rear wheel and the mating shaft in the final drive while the rear wheel is out.

Apr 15, 2010 | 2002 Yamaha Royal Star Venture

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...