Question about KTM Motorcycles

Open Question

2008 KTM 250XCW FORKS ARE STICKING

THE FRONT FORKS ARE NOT COMPRESSING AT ALL. ANY IDEAS ON WHERE TO START?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: Service manaul

Try this site I came across

http://sites.google.com/site/motorcyclemanualstore/

Posted on Aug 09, 2009

mwoodring1
  • 496 Answers

SOURCE: fork oil amount for a ktm sx65 2008

i can answer that in the morning i don't have my race tech book here at the house. but maybe i can help alittle more if you can tell me the weight with gear of the rider. I'll give you fuild wt. and amount around 10c am or call the shop at (361) 885-7787 10-6
Mark
C.C. Motorsports

Posted on Feb 22, 2010

wd4ity
  • 4565 Answers

SOURCE: My front fork o-ring seal is leaking, how do I

There is a seal in the "slider" of the front fork, the part that moves up and down. I haven't had a chance to work on the later forks but the earlier 41mm forks are quite simple.

Start by taking the drain plug out of the bottom of the slider and work the slider up and down to blow out all the oil. Then, remove the front wheel. Remove the top cap from the upper tube and loosen the top plug. Now, with the top plug loose, loosen the pinch bolts and slide the fork out of the triple trees. Remove the top plug carefully, There is a BIG spring in there. Once you have the plug out lift the spring out and set it asside. Notice the tapered end of the spring. It goes back in first. Turn fork tube upside down and allow as much oil to drain out as possible.

Now, look at the bottom of the slider where the axle goes. Up in a hole there is an allen head bolt. it is designed to use a special wrench but a regular 8mm allen key in GOOD shape will take the bolt out. It's best to use an air wrench to do this with. With the bolt out, the slider should slide right off.

Down inside the top part of the slider is where the seal is. Theres a snap ring, a spacer, and a seal. Replace the seal and put a little oil on it to assist reassembly. Put everything thing back together and add the appropiate about of oil. Since your forks are much larger than mine, I have no specs as to the quantity. The owners manual should tell you or a call to a local Harley dealer. Sorry but thats a good as I can do. There is a "wet" measurement and a "dry" measurement. Since you disassembled your fork, use the "dry" quantity of oil

Posted on Apr 19, 2010

Woods Goat
  • 85 Answers

SOURCE: My front forks on my 94 rm125 compress but won't

Most likely cause is worn bushings in the forks. This will require total disassembly and replacing the bushings along with the fluid and seals.


*Help me out. Rate me!

Posted on Jun 12, 2010

SOURCE: How much oil do you put in the front forks of a 2004 ktm sx 250

A good rule of thumb on anything that has a plug that removes to pour oil in, which I am assuming this one does, get it level and pour oil into it until it just starts to run out of the hole,. Again make sure it is setting level.
Gillight

Posted on Jun 22, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats the torque specs on the cylinder and head of a 03 ktm 125 sx


Thanks for contacting FixYa. I was reviewing some of the older un-answered questions trying to ensure your issue has been resolved.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

TF

Aug 19, 2011 | 2008 KTM 125 SX

1 Answer

Tied bike down in ute without using a fork block. Checked bike today and found both forks had leaked oil. I think bike tied down on way home has caused the forks to leak? Have the seals gone? or have they...


It's possible you may have leaked some oil, but first things first, clean the heck out of them and ride it around again to see if you are STILL leaking oil. If you have to top them up, there's a few methods out there, one guy I knew used a meter stick to measure the oil in the forks, but if you are going to be in there, you might as well drain the oil and start over with the correct amount of fluid. I hope this helps a little. Good luck.

Bruno

Nov 08, 2010 | 2008 KTM 450 EXC-R

1 Answer

2009 ktm 125sx torque settings for head and cylinder


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

TF

Nov 05, 2010 | 2008 KTM 125 SX

1 Answer

I need engine torque settings on my 2008 ktm sxf 250 motorcross bike


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

Try these:

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs
TF

Oct 29, 2009 | 2008 KTM 250 SX-F

1 Answer

What is te torque specs for the camshaft retaining bolts


Thanks for contacting FixYa. I was reviewing some of the older un-answered questions trying to ensure your issue has been resolved.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

\TF

Oct 28, 2009 | 2008 KTM 450 SX-F

1 Answer

530 exc spacing between front fork & spacer


front axle installation: looking at the front of the bike:

slide the wheel into position and insert the axle from the left. with axle now through the right hand fork, install nut and tighten the left fork pinch bolts to secure the axle for tightening the nut. tighten the nut to 29.5 ftlbs. and loosen the left pinch bolts. now tighten the right pinch bolts and compress the front suspension while the left (from front) is still loose. now allow suspension to rest naturally and tighten all 4 pinch bolts to 11 ftlbs.
your done.......the axle is tighten against the rotor side and the other fork is then tighten in it's natural position so as not to cause premature seal and bushing failure and increasing stiction.

Sep 27, 2009 | 2008 KTM 530 EXC-R

1 Answer

Leaking fork seals


Im replacing the fork seals on my 250yzf just wondering what the oil is thanx gary














Mar 15, 2009 | 2008 KTM 300 EXC-E

2 Answers

How to fill the front suspension on a ktm exc 2001


If you get the sevice manual or contact a dealer to get the correct oil amount for your bike, they need to know the model and year, you have to have the forks off the bike. take the fork caps off, take the springs out compress the upper fork tube all the way and add the specified oil. if they also give you the measured amount from the top that's the best way to get both fork oil levels exact. there is a special tool that you set the oil level in millimeters and it sucks out the oil to the right level, but before you do that step after adding the oil always pull and push on the cartage rod several times to remove air from the cartage tube. you will hear the air coming out and you will feel the changes in the cartage rod as the cartage tube fills up with oil and the air is removed.
something i'm confussed on though is if you replaced a seal you would have had to brake down the fork to replace it. you would have poored the oil into a container, cleaned all the internal parts,and used a fork seal driver to install the new seal. part of your question asks where do i put the oil in? thats in the open end of the fork after you have taken off the fork cap. It sounds to me like you only replaced the dust seal on one fork. that is not going to fix your leaking fork. you need to replace the oil seal thats pressed inside of the top fork tube.

Dec 01, 2008 | 2008 KTM 200 EXC

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...