Question about Honda Motorcycles

1 Answer

Cluth wont pump up no pressure

Rebult master cylender and slave sylender clutch wont pump up

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 31 Answers

It sounds to me like they can't get the hydraulic clutch to build up pressure. Without pressure, the clutch will not engage. It's a very simple system, consisting of two major parts. The clutch master cylinder and clutch slave cylinder. Replacing both of them (recommended) would get you a good clutch pedal again. This is assuming, of course, the clutch installation was done properly with no problems.

Posted on Nov 01, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: clutch master cylinder rebuilt, brand new clutch

Hi there,
Some times the clutch systems needs a vacuum
pump to bleed the system up to pressure. Also
note whilst bleeding the system don't let the reservoir run out of fluid. Also check if there is any other bleed nipples in this system. They all need bleeding.Hope this helps your problem.
Regrades Lighten



Posted on Apr 26, 2009

ga_drifter
  • 36 Answers

SOURCE: 1995 vn1500a9 clutch slips

if the bleeding temporarily helps you may have a bad master or slave cylinder, check the system really good for leaks. also check that your hose isnt pinched or cracked.

Posted on Jan 29, 2009

  • 3567 Answers

SOURCE: 84 honda shadow vt700 clutch slips when hot

Your clutch plates have lasted 25 years. It is probably time to get some new plates. Have your dealer get you a set of Barnett clutch plates.

Posted on Apr 22, 2009

watergatetec
  • 2 Answers

SOURCE: No clutch pressure

Its more than likley that you have an air lock in the clutch fluid ,try bleeding it again very carefully

Posted on Apr 29, 2009

  • 154 Answers

SOURCE: CLUTCH BUILDS PRESSURE AS IT GETS HOTTER.

try replacing the fluid on this and bleed system good,clutch adjust may be needed

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Could the pump that sends fluid to the clutch slave cylender be a issue with why my 5 speed 93 honda accord is stuck in limp mode?


That picture is of a power steering pump
the steering system and the clutch system are separate
clutch master cylinder really leaks majority of the time the slave cylinder seal on the trani leaks

Jul 15, 2015 | Honda Cars & Trucks

1 Answer

Is there a clutch ajustment


no clutch slave cylender inside transmission it is hydraylic check your clutch master cylender under you hood for full or empty level if mt most likely clutch slave is leaking car will have to remove transmission to reapair costly around $1000.

Apr 05, 2014 | 2005 Scion xA

1 Answer

4x4 6 cylinders manual trans.1995 ford f150 when down shifting and changing gears to slow down a very loud grinding sound but if i pump the cluth and rev up the rpm's sometimes it goes into gear.....


check and make sure your slave cylender is full of fluid, it should be mounted on the firewall, also sounds like you need to bleed the slave cylender.

Dec 03, 2010 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Cluth not working no prusher in cluth handle fluid good do you have to bleed it if so how


To bleed the hydraulic clutch actuator on your GL1200, follow the hydraulic hose from the master cylinder down to where it attaches to the engine. In this area you will find a bleeder valve just like the ones on the brake calipers. You will need an 8mm box-wrench (don't use an open end wrench), and a piece of tubing to slip on the bleeder valve in order to prevent hydraulic fluid from running onto the engine.

Make sure the master cylinder is to the "Full" mark with clean DOT3 brake fluid and then begin by pumping the clutch lever several times. While holding the clutch lever in, loosen the bleeder valve briefly, then re-close it. Do not release the clutch lever while the bleeder valve is open (doing so will draw air back into the system).

Repeat the above steps five or six times while also keeping the fluid level in the master cylinder topped off. If pressure within the system is not restored, then you will need to repair / rebuild the master and slave cylinders.

May 23, 2010 | 1985 Honda GL 1200 Aspencade Gold Wing

1 Answer

After traveling about 8km my car wont go into 1st or reverse gear. when it is cold it goes into all the gears fine. when i switch the car off it will go into gear. we did put a new(aftermarket clutch) in a...


Cluth cable ajustment if equiped.Some cars have a cluth cylender if your model has the cylender no ajustment is available.If you had your cluth changed at a garage you might consider takeing it back in for ajustments.If you changed the clutch check cluth cable for ajustment if your car is equiped with cable if not i would perhaps remove the transmission and inspect clutch for loose clutch plate or release bearing might not be seated properly hope this helped you.

Dec 24, 2009 | Mazda 323 Cars & Trucks

2 Answers

I changed out my slave and master cylinder in a 96 chevy camaro Z28. After doing so pushed down on the clutch to let out all the air bubbles from the new brake fluid. But the cluth is still soft, it has...


put a bar behind the clutch operating arm ,slacken bleed nipple on the slave then pull the bar back so it pushes the slave piston in.tighten bleed then release pressure on the bar ,and repeat a few times this should do it

Nov 20, 2009 | 1996 Chevrolet Camaro

1 Answer

1993 240 nissan clutch pedal acts like it has no fluid


Check if the slave cylinder is being activated by the operation of the master cylinder (also ensure no fluid leaks are present).
If slave cylinder not moved, you still have a faulty master cylinder or slave cylinder - or the hydraulic system still has air.

If the slave cylinder is operating normally and there is still no return pressure from the clutch pressure plate, you have a faulty pressure plate or throughout lever mechanism.

Aug 12, 2009 | 1993 Nissan 240SX

2 Answers

5 speed manual transmission wont shif gears while running


You probably have air in the system. You need to bleed the air out of the system so that it will disengage your clutch. The air in the system is compressing and, therefore, the slave cylinder can't reach the full extension.

Aug 04, 2009 | 1998 Pontiac Sunfire

1 Answer

Clutch peddle will not mash. we replaced clutch, presser plate, throwout bearing and master cylender and hose to slave cylender and clutch peddle won't mash you can take slave cylender loose fro...


when you bleed the system you need to force fluid from the slave cylinder up threw the master cylinder . this is proper way to bleed clutch system.

Jul 02, 2009 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...