Question about 2006 Victory Hammer

Open Question

How do you remove the seat from a 2006 Victory Hammer? I need to replace the taillight assembly.

Posted by on

  • mbroderhause
    mbroderhause Nov 02, 2012

    do i need to remove the seat? i need to replace the entire taillight. i baught a new one. please help.

  • mbroderhause
    mbroderhause Nov 02, 2012

    i figured it out. just need to remove the plate that is holding the license and rear turn signals.... it was easy.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 200 Answers

SOURCE: victory hammer headlight bulb replacement

Look for phillips screws around the front of the headlight bezel.Remove these and pull the headlight straight forward. Behind the light you now hold in your hand will be a 3 prong electrical connection that you either pull straight back or twist 1/4 turn. You will be replacing the whole headlight like a car or you will have a halogen bulb that twists out of headlight, buy a new one and reverse procedure for reinstall....good luck to you my friend....Tim

Posted on May 11, 2009

Ad
  • 1 Answer

SOURCE: wheres the oil plug on a 2006 victory hammer?

on the bottom of the crankcase, takes the allen key end of the multi tool (phillps screw driver/allen key) that's on the side of the battery box.

Posted on May 18, 2009

  • 1 Answer

SOURCE: how do I remove the rear brake calipers on a 05

Don't know if it is the same as on my 05 Kingpin but there is simply the axle nut holding it on and a groove in the swing arm. Once the axle nut is removed and axle is punched out of the way you must shimmy the caliper and it's male block casting down the channel in the swing arm to where there is a square cut out in the swing arm, once there it will just drop out of the swing arm. Putting it back is the same but. painful set-up compared to a few bolts.

Posted on Dec 21, 2009

  • 63 Answers

SOURCE: 2007 Victory Hammer

G'day, from what I can see from pics, your hammer should be disc brake rear. This means there's usually no need to remove the wheel. If you have a close look at it you should be able to see how the pads are removed. Some pads are held in by pins or bolts that pass through holes in the pad to hold it in, others are held in by the caliper itself & you'll need to remove it to change pads.You'll need to sqeeze the pistons back into the caliper if you're putting new thicker pads in. You can use a G clamp & old pad to do this, just keep an eye on the fluid res.hope this helps :)

Posted on Apr 12, 2010

e-Guru
  • 3917 Answers

SOURCE: removing fuel pump out of

Hi


Remove as much of the fuel as possible.
Remove tank
Turn upside down
Remove tank plug retainer clip
Pull tank plug
Remove nuts and washers which attach pump to tank
pull fuel pump thru opening where tank plug was
replace all o-rings, washers along with fuel filters on pick up tubes since your already there.
Then just reverse order for re-install.


Please accept the solution if it's helpful. Do get back to us for any further query.

Thanks for contacting fixya.com

Posted on Sep 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I purchased a l.e.d. tail light and a voltage converter for my 06 hammer. First thing, I followed all instructions that came with both parts! When I plug in the converter, I don't get running tail...


Hi, Bcfdffhudson I feel your pain, I just went through the same thing with my 2003 Harley. I did some research and soon discovered that all of these fancy tail light/turn signal/brake light Led conversion kits are "JUNK" I ended up rewiring the stock rear lights myself for my own personal requirements, it was a pain in the arsenal but it only cost me $30 and a lot of time.
For more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Victory Motorcycles Motorcycle Forums
Victory Motorcycle Tail Light Voltage Converter for Vegas Jackpot Hammer...
http://www.granitestatechapter.com/mydata/05-06%20Hammer_06%20Jackpot_Service_Manual.pdf
Motorcycle Service Parts Part Finder Victory Motorcycles Store
2005 Victory Hammer Owner Manual

Jun 05, 2017 | 2006 Victory Hammer

1 Answer

How do you get the battery out without removing the seat of a 2006 hammer


Hi Edelp, for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day. http://www.granitestatechapter.com/mydata/05-06%20Hammer_06%20Jackpot_Service_Manual.pdf

Mar 01, 2011 | 2006 Victory Hammer

1 Answer

HOW DO I CHANGE THE REAR BULB ON A 2006 BUICK LACROSSE


Asuming you mean taillight/turnsignal, and not highmounted brake light:
1.open the trunk
2.Remove 4 wingnuts on trunk trim (there are two on each side)
You can do it by only removing 2 on one side, but it makes a nicer job,
3.Pull back the trunk "trim" the carpeted cardboard
4.Remove 2 wingnuts which hold the taillight assembly in place
Pull out the taillight assembly; you might want to remove (i.e. unattach or unplug) the wiring harness
5.Turn the particular bulb's socket (there's 5 back there: 2 tail, 1 back up, 1 side marker, 1 brake/turn) counterclockwise, and it removes from the assembly, holding the bulb.
6. Pull out bulb and replace.
6. Reverse steps to reassemble.

Dec 30, 2010 | 2006 Buick LaCrosse

1 Answer

Need to remove seat to replace battery.


you dont need to pull the back sit ,just take the side chrome off use the allen wrench on the side of battery to remove the chrome ,and there are 10mm bolt to remove after that and you are donr. good luck

Sep 04, 2010 | 2006 Victory Hammer

1 Answer

Replace taillight assembly on 2006 Uplander


open tailgate, remove 2 screws holding assembly in place. Pull tail lamp rearward to disengage 2 retainers on backside of assembly. Unplug connector. Replace assembly or bulbs now as desired

Mar 05, 2010 | 2006 Chevrolet Uplander

1 Answer

Low beam not working on my 2007 victory hammer, is anyone else having problems with this?


your bulb is probably burned out. Remove the four screws that hold your headlight assembly together and take a look.

Jul 27, 2009 | 2007 Victory Hammer S

1 Answer

Wheres the oil plug on a 2006 victory hammer?


on the bottom of the crankcase, takes the allen key end of the multi tool (phillps screw driver/allen key) that's on the side of the battery box.

May 16, 2009 | 2006 Victory Hammer

1 Answer

Replacement of rear outside tail light assembly


If you're asking how do you change a taillight bulb, then follow this procedure:

Open the trunk lid.

Disconnect the connectors from the taillights (taillight bulb connectors are visible by looking inside the trunk at the back of the tail lamps.) There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in.


Brake Lights/Taillights: 21/5 W

Rear Turn Signal Light: 21 W

Back-up Light: 21 W

Rear Side Marker Light: 5 W


Turn the bulb sockets 45 º counterclockwise to remove the bulbs.


If you're removing the taillamps with the bumper off there are 3 nuts and screws that hold the taillight to the rear panel of the car that have to come off from the inside of the trunk.
Remove the nuts and screws, then remove the taillight.

hope that answers your question

Aug 15, 2008 | 2006 Volkswagen Jetta

Not finding what you are looking for?
2006 Victory Hammer Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Victory Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4533 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

Are you a Victory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...