Question about Motorcycles

2 Answers

Auxiliary jr80 when going fast will choke itself and gas will drain out tub

Run fine when going slow

Posted by on

  • paul Oct 31, 2012

    what tub?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 46 Answers

If by tub you mean carburetor, you have either a stuck float, or it needs to be adjusted, your float level might be set to high. i have never heard of a carb being called a tub..

Posted on Oct 31, 2012

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Im guessing its draining out the carby. you will need a new orifice, also make sure the float isnt broken or has holes. clean the carby really well

Posted on Oct 31, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: bike will not idle witout having choke on a bit

I have a supermagna and used fuel stablizer once and it wasnt fit it gummed my carbs up,ive cleaned mine often and it isnt rocket science,remove the tank airbox assembly,loosen up the boot flanges that hook the carbs to the motor(ones on carb)then remove the carbs,then the cables,choke and throttle,do not remove carbs from assembly(leave all 4 together)remove the bottoms and tops of a carb,removefloat and jet,then remove all the brass jets and clean them so you can see through holes,,blow out all the holes in carbs,and reasemble,works for me every time,about two hours to do,good luck

Posted on Apr 05, 2009

  • 20 Answers

SOURCE: runs great at hwy speed pops and slow response when you stop

Sounds like a lean condition. Adjust the carburator for a richer idle mixture.

Posted on Apr 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Suzuki jr80 takes too long for rpm to get back down to idle , after throttle is released. wasnt run for couple yrs. completely disassembled carb and cleaned. it starts 1-2kicks.not setting correctly?


Hi, Troy and the usual suspects are:
1. Throttle cables improperly adjusted, pinched or need lubrication.
2. Idle adjusting screw needs to be backed off.
4. Air fuel mixture adjusted too lean start with 2 full turns.
5. Intake system air leak.
6. Fast idle choke ramp is not releasing.
7. Broken throttle return spring.
8. Damaged diaphragm or slide.
9. Faulty MAP, TPS, ATS, O2, sensors or wiring/connector
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Lazy Slow Return to Idle or Erratically High Idle
2 Stroke suzuki JR80 tuning help
http://www.soemyanandarthetlwin.com/hwa/suzuki/suzuki-jr-80-service-manual.pdf
OEM parts for Suzuki
Suzuki DS80 and JR80 Motorcycle Cyclepedia Online Service Manual
Suzuki JR50 Owner Manual

May 25, 2017 | Suzuki Motorcycles

1 Answer

A 89 suzuki sidekick ideal fast when cold when it warm up ideal slow down is this normal


Yes you car chokes itself and runs more gas and less air as the air expands more when cold which makes your car idle higher if it didn't do this it would actually die.

Dec 13, 2013 | Cars & Trucks

1 Answer

Stihl 090 Chainsaw carburetor get way too much gas at high speed, even though HS jet is completely closed.


You have an internal circuit leak in the body itself, my friend. Get a new carb, it's still going on a $1000 saw and will make it run like new again.

Jul 05, 2012 | Stihl Chain Saw 051 075 088 090 +

1 Answer

My troybuilt yard pony riding lawnmower will start with the choke fully open and then dies immediatly when you take the choke off. It will only start and run with the choke fully open, but dies after 20-30...


Do you mean that you can start it normally using the choke (that would be choke CLOSED), but then it dies immediately when you move it to run (that would be choke OPEN)? And if you leave the choke in the starting position that it dies after 20-30 seconds?----- If I have that all right, then you definitely have a restriction in the gas supply. Drain all of the gas from the mower and don't use any old gas. If you have any more old gas (from last season) don't use it. If this mower has a gas filter, replace it. Put just a little fresh gas in the tank plus a little of the cleaner. Start it up, do that a few times if needed. Use a fuel additive such as Sea Foam to keep the gas from gumming up so fast.

Mar 15, 2010 | Troy-Bilt Garden

1 Answer

Won't empty water slow spin in spin cycle


It spins, but doesn't pump If your washer spins but doesn't pump the water out, the drain line is probably clogged. In many washers, a small sock or other piece of clothing can get between the clothes tub and the outer tub that holds the water. If the clothing gets between the tubs, it may then get into the drain hose that's attached to the pump--or even into the pump itself. If it's in the pump, you need to remove the hoses from the pump and pull the item out.

To remove the sock from the outer tub port, open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then, using needle-nose pliers, try to grab and remove the clothing through the port.

Sometimes you can't remove the stuck clothing from below. Then you have to remove the agitator, top of the outer drum shield, and inner clothes tub. This isn't easy to do--and you may need special tools--so you might be happier getting a qualified appliance repair technician to do the job.

If the drain line isn't plugged, the problem may be with your pump. Even if the pump appears to be turning, the internal impeller may be broken. If so, you need to replace the pump.
if this helps please vote a fix ya

Jul 15, 2008 | Maytag PAV2300 Top Load Washer

2 Answers

Washer won't spin fast, only slow


tyr removing the lower acees panel from the uint , ther is a "button trap" located there to catch debris from entering pump assy, chances are its clogged and if it cant drain all the water it wont go into high speed spin, also you MUST use an HE detergent. HE detergent specifically designed for front loading washers

Apr 28, 2008 | Kenmore 44102 Front Load Washer

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...