Question about kawasaki Motorcycles

Open Question

Specs for head bolt torque on 02 Kawasaki EN500

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 160 Answers

SOURCE: What are the Torque Specs for a Kawasaki Bayou 350 ATV?

which specs do you need engine ?

Posted on Nov 12, 2008

  • 254 Answers

SOURCE: Need torque wrench settings for cylinder head bolts

try here http://www.manualz.info/

hope this helps

Posted on Jan 04, 2009

bunnydawg
  • 5158 Answers

SOURCE: 91 kx 250 torque values

Engine Top End:
Auto Decompressor Bolt 104 in·lb
Cylinder Head Cover Bolts 87 in·lb
Cylinder Head Bolts: M10 36 S
M6 104 in·lb S

the S in that means the specified pattern ... just like tightening car tire bolts... please note all that it its INCH lbs....

don't know why it says just 36 for the M10 bolts unless they left out inch lbs

Anything else let me know as i've got a manual for the 250 f... actually i've got a few different ones

Robert

Please take a moment to rate this solution as i've taken a few minutes to find the manual thanks

Posted on Jan 28, 2009

chuck943
  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

polarcycle
  • 1392 Answers

SOURCE: head bolt torque spec

Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove tight bar end bolt holding chrome weight on kawasaki en500 in order to renew twist grip throttle


Hi, Douglas that screw has factory Loctite that's a pain to remove a little propane heat at the screw head works wonders.
For more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Removing replacing bar ends
Throttle Bar End Wont Come Off
Kawasaki EN500 Service Manual
OEM Parts for Kawasaki
1993 Kawasaki Vulcan 500 Owner Manual

Jun 20, 2017 | kawasaki EN 500 Vulcan Classic Motorcycles

1 Answer

What is the head bolt torque for


Not having a manual or knowing the bolt thread size ..I would be guessing...can't guess!!!
Being a diesel the torque will have be very close to factory spec's.. no more that 10% above factory spec...I do not have a manual.. google the specs..sorry

Mar 06, 2016 | kawasaki 2007 Mule 3010 Trans 4x4 Diesel

1 Answer

1985 Zl900 cyl head bolt torque specs


You also work your way in pairs from the inside out, NOT cris cross as many other applications.

Some IMPORTANT info here. Should apply to most same era/ 900's (84/85/86).


8825b93f-94d0-4d63-9dd5-d8d937a30d00.jpg

4f83d264-0840-42ba-9788-6452ae087f0e.jpg

01038193-390b-4312-8b2a-0b595e268860.jpg

Apr 22, 2014 | kawasaki ZL 900 A1 Eliminator Motorcycles

1 Answer

Husky model VT631502AJ head torque specs


I am certain there are torque specifications but I don't know what they are. You might be able to get them from the manufacturer. Lacking that, determine what the bolt strength (usually indicated by marks on the bolt head) and with the bolt strength and size you can determine what the appropriate torque would be for that size bolt. Too little torque and the head will leak. Too much and you will strip out the threads or twist off the bolt head. A 13mm head is nominally a 1/2", which is not a very large bolt head thus the bolt shank is not going to be particularly large, probably somewhere in the 7 to 9 mm range. Check online for torque specs. If you can't identify the specific bolt strength I would assume it is the lowest normal value for that size bolt. There shouldn't be any particular reason for using high-strength bolts in this type of application.

Aug 03, 2012 | Air Tools & Compressors

1 Answer

What are the torque specs for head cover bolts on a 2008 ninja zx6r?


If you mean head bolts you need to ask a dealer, if you mean valve cover bolts you can look up torque spec's by bolt size just google it look for a flow chart of spec's.

May 06, 2012 | 2006 kawasaki Vulcan 800 Drifter

1 Answer

What are the torque specs for cylinder and head bolts on a 2001 kx 250?


The torque specs for your cylinder base nuts are 25ft.-lb.and the head flange nuts at 18ft.-lb.tighten them in criss cross pattern,at three different stages,ex.25ft.-lb.start with 8 then15 then 25,18ft.-lb.start with 5 then 10 then 18.good to go.Hope this helps.

Feb 08, 2011 | kawasaki KX 250 Motorcycles

2 Answers

Replacing the hubs and rotor on my 02 ford excursion i need torque specs


just pull them up tight and dont forget to oil the bolts first so they dont corrode ,the smaller the shank of the bolt the less torque it needs so a bolt with 17mm head would be about 55 or so 19mm head 70 or so it is not rocket science tightening a bolt

Aug 12, 2010 | Ford Excursion Cars & Trucks

1 Answer

What are torque specs. for klx110 head bolts?


the torque specs for the head is 16 lbs.

Jul 12, 2009 | 2006 kawasaki KLX 110

2 Answers

NEED TORQUE SPECS AND SEQUENCE FOR 02 DODGE 2.4 V6 STRATUS


  1. Tighten bolts in sequence shown in (Fig. 23), using the following steps and torque values:
    • Step 1: Bolts 1 - 8 to 48 Nm (35 ft. lbs.)
    • Step 2: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 3: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 4: Bolts 1 - 8 to +90° . Turn Do not use a torque wrench for this step.
    • Step 5: Bolts 9 - 11 to 28 Nm (250 in. lbs.)
  • I tried to send a pic of the head bolt numbers but it wont let me so e mail me dbern002@att.net have a good day DB

Feb 01, 2009 | 1997 Dodge Avenger

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...