Question about 2005 Bajaj Pulsar 180

1 Answer

Carburator screws damaged

Hi, My pulsars 180 ug4, 2009 carburator screws slipped and not able to open it. Please provide some solution

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 338 Answers

Hi ok i am assuming you stripped the phillips heads and connot turn the screws to take them off.
2 ways to loosen them 1 mini set of locking pliers or get a small metal punch and a small ball peen hammer try and secure the carb so it wont be damaged and take the punch mak sure the tip is sharp enough on the outside edge of the head of the screw make indentation and hit it in the counter clockwise direction it will come loose then screw it the rest of the way out replace them with new screws when you put it back together.

Posted on Nov 03, 2012

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rony_masc
  • 83 Answers

SOURCE: Can any one provide electrical wiring diagram for

wiring diagram will be found in pulsar manual, that you got from Vehicle. then if you dont have that one, Xbhp is a website that will have pulsar manual. try check it out!

Posted on Feb 02, 2011

  • 2712 Answers

SOURCE: Gearbox not smooth in Pulsar 180

Because its one gear front and four as back so it doesnt smooth..

Posted on Nov 10, 2008

seanpwright
  • 2030 Answers

SOURCE: I need a new carburator for pulsar 150 dtsi 2005

Once you find a dealer just simply tell them you need a new carb. they will know which ones it is

Posted on Aug 27, 2009

FirsLonewolf
  • 186 Answers

SOURCE: can i fix pulsar 200 cooling system for pulsar 180

measure the overall dimensions and the mounting brackets, if they are the same it can be used

Posted on Nov 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought my new pulsar 150 bs4 engine and its 3 months from the day of purchase i have faced three times a same problem of leakage of petrol from carburetor can u plz suggest permanent solution


Hi, Vinaymatthew and the usual suspects are:
1. Damaged or restricted fuel tank venting system.
2. Loose float bowl screws.
3. Damaged float bowl o-ring.
4. improper fuel level in the float bowl.
5. Worn or dirty inlet valve or seat.
6. Damaged or leaking float assembly.
7. Particle contamination in inlet fitting cavity.
8. Damaged petcock diaphragm allowing fuel to flow through the vacuum line into the combustion chamber.
9. Contaminated fuel tank.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
petrol leaking from carburetor
Pulsar150 carburetor Repair
Bajaj Pulsar 180 DTSi Workshop Manual
Shop At Bajaj Pulsar 150 Classic Bike Parts And Accessories Online Store...
Bajaj Pulsar 150 Maintenance Manual

Jul 02, 2017 | Bajaj Pulsar 150 Motorcycles

1 Answer

My pulsar 150 engine is seized due to less oil what to do


Hi, Abhimanyu sorry to hear about your misfortune you will have to disassemble the engine and inspect for damage for more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Bajaj Pulsar 180 Engine Work Required Suggestions Please
http://www.xbhp.com/talkies/general-biking-discussion/25758-when-did-you-motorcyles-engine-seize.html
Bajaj Pulsar 180 DTSi Workshop Manual
Bajaj Pulsar 150 DTS Owner Manual
https://www.speedzz.com/vipar-bajaj-pulsar-150-ug-2-engine-parts.html

Jul 11, 2016 | Bajaj Pulsar 150 Motorcycles

1 Answer

What is the cause of low pickup pulsar


Hi, Anonymous and the usual suspects are:
1. Throttle cables misaligned or misrouted.
2. Damaged or restricted fuel tank venting system.
3. Inlet system air leak.
4. Vacuum piston malfunction.
5. Accelerator pump leaking or no output.
6. Plugged bowl vent.
7. Fuel level in bowl too low.
8. Restricted fuel supply passages.
9. Plugged jets or passages.
10. Worn or damaged needle or needle jet.
12. The enricher valve not seated or leaking.
For more information about your issue please visit the websites below. Good luck and have a nice day.
DOWNLOAD Bajaj Pulsar 180

Apr 08, 2014 | 2011 Bajaj Pulsar 180

1 Answer

IGNITION NOT WORKING


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
DOWNLOAD Bajaj Pulsar 180

Mar 16, 2014 | 2011 Bajaj Pulsar 180

1 Answer

Hi, I am not able to start my pulsar 180cc. It


Hi, Aditya and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day. DOWNLOAD Bajaj Pulsar 180

Sep 17, 2013 | 2006 Bajaj Pulsar 180

1 Answer

Pulsar 200 pulling back while accelerating


Hi, Anonymous and the usual suspects are:
1. Throttle cables misaligned or misrouted.
2. Damaged or restricted fuel tank venting system.
3. Inlet system air leak.
4. Vacuum piston malfunction.
5. Accelerator pump leaking or no output.
6. Plugged bowl vent.
7. Fuel level in bowl too low.
8. Restricted fuel supply passages.
9. Plugged jets or passages.
10. Worn or damaged needle or needle jet.
12. The enricher valve not seated or leaking.
For more information about your issue please visit the websites below. Good luck and have a nice day.
DOWNLOAD Bajaj Pulsar 180

Feb 14, 2013 | 2007 Bajaj Pulsar 180

1 Answer

Hi,got a bajaj pulsar 180,the self start doesnt work,the horn and lights dont work unless i rev it. Whats the problem? It dims the screen also


Hi, Splatme2 and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
DOWNLOAD Bajaj Pulsar 180

Sep 10, 2011 | 2007 Bajaj Pulsar 180

1 Answer

In pulsar200 2009 model, How to increase the pickup,power,Speed?


Hi,

Check your gasoline filter if there's one, check the air filter, also check or just replace your spark plug(s)...

Most other things that should be done by a mecanic are like maybe cleaning the carburator(s), checking the ignition, see wether there is damage inside the cilinder...

I hope this is helpful, and greetings,

Olivier.

Oct 22, 2009 | 2007 Bajaj Pulsar 180

11 Answers

Da price of pulsar 220 headlight


220 mask price is 2000
headlight- 4000
jal- 700
handle ,tee-1300
and easily fit in pulsar150

Apr 06, 2009 | 2007 Bajaj Pulsar 150

Not finding what you are looking for?
2005 Bajaj Pulsar 180 Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bajaj Experts

sachin sharma
sachin sharma

Level 2 Expert

171 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Joseph Gallucci

Level 2 Expert

120 Answers

Are you a Bajaj Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...