Question about Motorcycles

Open Question

Bultaco kickstart return spring fitting - Motorcycles

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 34 Answers

SOURCE: My 150cc Lifan(Chinese) scooter kickstart won't

It sounds like the gear inside the Left cover is not linged up right i have the same motor and this web site bailed my out of this problem go to it is a great frourm to find all the manual and repair how to fix your scoot For your info the motor on your scooter is known as a GY6 engine parts are all over the place. is where i get some of my parts. let me know if you need any more help.
Best Reguards


Posted on Jan 11, 2010

Testimonial: "Thanks Larry, I waill check it out!"

  • 1508 Answers

SOURCE: Can i use a cr 250 kickstarter return spring on my

They are probably the same part anyway,
there may be a problem with the installation.

Posted on Jun 17, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hey there my scooters kick start is jammed up and hard to move. any ideas?

Your return spring inside the kick start is either broken,jamed or need to remove the attachment bolts and see what is up with it..if the spring is broken and you have no place to get one can put the kicker back in without the return spring in temporary to start..but you must pull the kicker into the push down "start" position each time you want to kickstart it..good luck

Oct 22, 2014 | Motorcycles

1 Answer

Rg 150 kickstart not returning

The spring must be "wound" to be tight and make the kickstart lever return..

Jul 07, 2017 | 1998 Suzuki RG 150 Gamma

1 Answer

I just bought an 1987 Yamaha TT350 dirtbike. is it a 2 cycle and how do i change the kickstart shaft

Hi, a yamaha TT350 actually has a 4 stroke engine. To replace the kick starter shaft, You need to remove the crankcase cover on the kick starter side of the engine..
The clutch basket etc will then have to be removed. '
You then use a set of needle nose pliers to unhook the kickstarter return spring from its post in the crankcase.
Release the return spring and allow it to relax. Then rotate the kickstarter assembly counterclockwise by hand , and remove the shaft assembly from the crankcase. Reverse this process to refit.
You can buy cheap workshop manuals for the yamaha XT/TT 350 models. Clymer manuals make them, there are usually good second hand ones on ebay etc,
the XT/TT350 workshop manual number is
These workshop manuals are a "must have" when working on bikes or cars etc, and by following a manual, at least you'll know that the job has been done safely and 100% correctly.

Apr 01, 2011 | Yamaha TT-R 250 Motorcycles

1 Answer

When i kick my kick start over it stays down and you hear a grinding noise inside , can anyone help thanks jon

It sounds like your kickstart return spring has gone. The noise you hear with the kickstart still down is because it is still engaged. Dont let this happen, return it to the upright position. You will need to take the case cover off and have a look. On many bikes this spring can be replaced very simply, on others you may need tp strip the engine further. It would be worth investing in a workshop manual.

Nov 14, 2010 | 2001 Honda Cityfly

2 Answers

1986 xr250 kickstart binding up release clutch cover and works fin tighten bolt and binds up again

The problem was Alloy spacer inside spring that supports spring had turned. Not allowing for shaft to fit in proberly

May 24, 2010 | Honda Xr 250 Motorcycles

1 Answer

My 125dt dosent sart or kick sart,the gear inside have a bushing in shafting?or it was broken..

Common cause of kickstarter not engaging(I am guesing that this is your problem) is a broken spring on the kickstart mechanism,or that the kickstart idler gear cerclip has fallen off(this allows the idler gear to move forward on the shaft & thus won't allow the kickstart gear to transfer drive to the clutch hub).Remove clutch cover, put kickstart lever back on shaft spline,activate kickstart lever by hand(easier with sparkplug removed+in neautral)as kickstart lever moves down 90 degrees the gear on the kickstarter mechanism should move out to engage with gear next to it(kickstart idler gear).If the gear on the kickstarter mechanism dosn't move outward it has a broken spring on the kickstart mechanism.replace spring and all should work.(if the spring is broken you need to try find the broken piece with a magnetic pick-up tool as the broken part can cause further damage if not removed)To do this job I highly recommend you first purchase a workshop manual which will guide you through these processes.After all a manual is the most valuable tool in your tool kit.

Nov 17, 2009 | 2003 Yamaha YZ 125

1 Answer

Fitting back kick start spring mechanism derbi senda drd rro 50

Hi I have a derbi senda sm 2005 Just brought a kickstart shaft but carnt rember how to fit it n how the springs go If any1 can help please let me no

Oct 14, 2009 | 2004 Derbi Senda R 125 4T

1 Answer

Kickstart return spring on a 2002 Polaris Scrambler 90

You should be able to replace the spring by removing the side case

Jun 08, 2009 | 2002 Victory V 92 C

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

76846 Answers


Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides