Question about Motorcycles

Open Question

Plessey ducon capacitor wiring diagram 50hz

Require for re-wire of cement mixer

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 81 Answers

SOURCE: NEED A WIRING DIAGRAM FOR A A200 HOBART MIXER

I have a wiring diagram for the standard A-200. If you send me your e-mail to me I will send it to you. capt_rick1912@yahoo.com

Posted on May 31, 2008

Ad
Just_Bobz
  • 448 Answers

SOURCE: Wiring hard start capacitor in GE refrig

I would go back to person who gave that advice because just the right touch on that capacitor and YOU my friend will be in the hospital. If this is helpful, please post as such. TY

Posted on Jan 17, 2009

RCtech
  • 55 Answers

SOURCE: have new switch for belle 110v cement mixer

This should be pretty easy. you should have either two or four wires in the box and two or four hook ups on the switch. the wires in the box must stay aligned with the matching colors so if your switch has four connections but you only have two wires hook them up to the post opposite each other top to bottom. (they need to both be on the same side) if you have four wires but only two switch posts wire nut the two white (or blue) together and switch the black (or brown). The important thing to remember is the power needs to come in on go into the switch or breaker first.

let me know if this wasn't helpful

Posted on Mar 28, 2009

jgwhomeequip
  • 1902 Answers

SOURCE: Start Capacitor wiring diagram needed

When hooking up capacitor on a pump it doesnt really matter which way the wires go. The capacitor is set up in such a way the it supplys power wherever the wires are hooked up. I hope this helps

Posted on Jun 02, 2009

  • 39 Answers

SOURCE: femsatronic wiring diagram required

Femsawhat? Anyways I have had three of these bikes and I'm guessing that you are asking for an aftermarket component wiring diagram. I'd run with Zeeltronics simply because the service support is there. Anyways, try yamaha-rd.com, the guys on the forum are absolute gurus and most of em eat, sleep and breath this stuff. Don't trust Billy;)

Posted on Dec 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A belle cement mixer,wont stay on when start button is pushed,changed switch ,still the same?


Sometimes the most simplest of fixes is verifying that you have voltage at your outlet and that you have voltage getting to the motor.

Check the motor's overload button; reset if necessary.
Take resistance readings:
  • start capacitor
  • run capacitor
  • and motor

If anyone of their specs are out of whack, that's the component that is defective and will need to be replaced.

Mar 24, 2015 | Masonry Tools

1 Answer

The wires have come out of the switch


take it to an electronic repair shop in town karen don't fix yourself!

Mar 22, 2014 | Bell Labs Protecta Load-N-Lock Anchoring...

1 Answer

I need wiring layout for husky cement mixer?


Cement mixers aren't motorcycles. You could try asking Husquvarna for a diagram, they will definitely have one. It can't be that complicated thiough. They are usually diesel and so only have a very basic electrical system, Start and stop circuits and maybe a heater for the engine.

May 11, 2013 | Motorcycles

1 Answer

Hi, My cement mixer 240v supply lead has been pulled out of the connection box. Can anyone supply me with a wiring diagram. the only detail on the box is that it was made by POWERFLO drum capacity...


Do you still have the wire with plug end?
The mixer has a switch.
Is the mixer reverse-able?
Or is the mixer 2-speed?

What do you mean about 'one plug' and 'second plug?'

Buy cheap multimeter at hardware. Install battery. Set to read ohms.
Green wire is always ground.
Test each wire to each other.
For example if you test green wire to metal side of mixer, the meter will show full open circuit.
Test each other wire to each other wire. When voltage travels through the motor, then there will be ohm reading.
Move the switch to each position, and see which wires test differently.
Try to identify wires going to switch.

240Volts will have two hot wires.
One or both the Hot wires should connect directly to switch, depending if switch turns one hot wire on-off, or turns both hot wires on-off.
In a two speed system, or reversing system, the switch will send power to different coils on motor.

Sep 27, 2012 | Dryers

1 Answer

I need wiring diagram for Belle 150 cement mixer 110v


Small BLUE at top right hand corner, then the two rows of two...
top left is BLACK, top right is GREY, bottom left is BLUE from the power supply and bottom right is a short BROWN wire with a spur, which leaves a BLUE to connect to the spur. should be it :)

Oct 09, 2010 | Garden

1 Answer

WIRING OF A 200 WITH A SINPAC CV25A DEVICE AND START CAPACITOR, 115V


Here's a wiring diagram I snatched out of the technicians service manual....

e5067cd9-581d-4aba-af19-b1124644e869.jpg

Aug 11, 2010 | Hobart A200 Stand Mixer

3 Answers

Hobart A 200 Mixer


There are four possibilities to look at here. Assuming your mixer has a normal capacitor start motor (older a200's used a different style motor), possibilities are, in order of likelihood:

Motor start capacitor
Start switch (electronic or mechanical)
Burned wiring
Motor start winding

The start capacitor is located at the rear of the mixer. Remove the rear cover (4 screws) and pull the cover towards you. Disconnect one wire from the capacitor and test with any multimeter.

The start switch, if electronic, is able to be tested, but not very easily. Once you've eliminated the other possibilities, it's time to replace the (electronic) start switch. If the motor has a mechanical start switch, it's easy to test: Remove the two wires at the rear of the motor and test for continuity with the motor stationary. A multimeter should show near zero ohms for a good mechanical start switch.

Burned wiring should be easy to spot with some careful inspection around the motor, capacitor, and start switch.

Start winding: Look closely at the stator (stationary part of the motor). If some of the copper windings look significantly darker in color than the others, it's likely the start windings were overheated (the start windings are the thinner copper wires - if you look closely, approximately half of the wires are thinner than the other half). Look for a wiring diagram behind the power switch and determine which wires leading to the start switch and/or capacitor are for the start windings and test for continuity across the start winding. You should read a fairly small value such as 5 - 15 ohms. Values significantly outside this range could indicate a partially open or partially shorted start winding.

Jun 09, 2010 | Hobart A200 Stand Mixer

1 Answer

What is the power input voltage required to operate the phonic 1805x audio mixer? is this an AC, or DC input? unit missing power supply and needs to be bench tested for possible future use. no manual...


i have seen the manual. most mixers use ac mains supply with smps inside with +48V for phantom and ur mixer is one of those. u will see a three pin mains connector at the back. but phonic made these mixers for different countries. for us/canada 110~120Vac/60Hz - for uk/australia  230~240Vac/50Hz, europe/ asia 220~230Vac/50Hz.
Look for these or a voltage selector near the power input terminal. if u do not find any of these one sure way of finding which mains supply u should use is to open the case and look at the biggest rectifier filter capacitor on the smps board. 110~120V supply will have capacitors working voltage around 250Vdc and for the others around 400Vdc working voltage. (eg 1000uF, 250V or 1000uF, 400V)
so depending on the DC working voltage of the filter capacitor and country u either step up or step down the mains supply. 
18Vac supply will never work.!
the rated mains voltage sometimes are printed on the smps board itself. Hope this helps. 

Mar 13, 2010 | Electronics - Others

1 Answer

A - 200 3 speed mixer needs a wiring diaram


how do you know diagram is wrong , you could have wired it wrong the timer kit i belive comes with 3 or 4 different diagrams for that mixer you need to pick the right one

Aug 27, 2009 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...