Question about 1991 Suzuki VS 1400 Intruder
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The Intruder does handle fairly well compared to its' counterparts of the cruiser class, by handling I would assume your talking about how well it behaves in turns...since this class of machine IS the cruiser type do not expect to keep up with the current or past generations of sportbikes as you will fall behind. The best scenario is SMOOTH sweeping turns, the suspension in its' current form cannot deal with irregularities in the road...sportbikes' suspensions are meticulously calibrated for these real world curcumstances...cruisers cannot do this. The raked out front forks of cruisers make for a very stable platform but are not designed to be turned hard. A simple modification that I would myself do if I had a cruiser, would be the addition of a fork brace...a chunk of aluminum that strengthens the two front fork tubes..so that they don't flex (As much!). In addition I would pay attention to the exaust setup, footpegs and any other hard parts that would interfere with agressive cornering(Lean angle).Some exausts hang SO far down on cruisers that they really limit how far you can bend er over...all that stuff needs to be removed, changed or modified so you can corner good up to the suspensions limit.
Posted on Nov 10, 2008
Did you sync the two carbs? If not the rear may be getting all the gas from the rear carb and none to the front. Twist throttle engine off and see if front carb cable is pulling the carb open.
Also unscrew the spark plug boot from the front spark plug wire and trim 1/8th inch off the wire and screw the boot back in. The plug wire end may be corroded on that wire.
Posted on Feb 08, 2010
One the left-hand side of the bike (facing forward), there is cover plate just ahead of the drive shaft. Remove that cover (mine has 8mm bolts). The bleeder valve is under this cover. Go to an auto parts store and get a "one man bleeder kit" or if you have some plastic tubing that will fit over the valve, you can use that and a clean jar. Follow the instructions on the bleeder kit, or if you're using the jar and tubing, fill the jar about a quarter of the way with break fluid (use DOT4, but never DOT5!). Take the cover off the master cylinder up at the handlebars, place the tube over the end of the bleed valve (after loosening it a turn or two. Place the other end of the tube down in the break fluid in the jar. Work the clutch lever until you stop getting bubbles in the jar. Be sure to keep the fluid level up in the reservoir. Tighten the bleeder valve, remove the tubing, top off the fluid and replace the covers.
Be careful not to get brake fluid on anything. It will eat paint and mess up other things.
Posted on Feb 13, 2009
Tips for a great answer:
Nov 07, 2016 | 1999 Suzuki VS 1400 Intruder
Nov 08, 2015 | 1997 Suzuki VS 1400 Intruder
Oct 22, 2015 | 1995 Suzuki VS 1400 Intruder
Jul 02, 2014 | 1994 Suzuki VS 1400 Intruder
Apr 16, 2013 | 1998 Suzuki VS 1400 Intruder
Oct 24, 2012 | 1991 Suzuki VS 1400 Intruder
Jul 28, 2010 | 1995 Suzuki VS 1400 Intruder
May 26, 2010 | 1994 Suzuki VS 1400 Intruder
Mar 05, 2010 | 1994 Suzuki VS 1400 Intruder
319 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: