Question about 2006 Derbi GP1 125

1 Answer

Not starting properl doesent seem to engage - 2006 Derbi GP1 125

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 948 Answers

Some things to check:
Is your battery fully charged and does it have the proper amount of electrolyte? Use a multi-meter across the battery terminals, you should get around 13v (direct current). Watch the meter as you try to start the scooter, if the voltage drops a lot your battery is probably bad.
Is your starter button working? When you press the button do you hear a click or get any indication it has been pressed? Has there been any damage to the switch area recently?
Is the starter working? Do you hear the starter turning the engine over, or is the starter just spinning? If just spinning and your battery is good, check your starter solenoid.

Posted on Jan 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vauxhall Astra 1.8 Sri turns over not starting brake lights jammed on coil pack seems ok no fault codes in system


Ok may be more than one fault here
Firstly the brake lights may be down to a fulty brake light switch
this is under the brake pedal.
Secondly the Starting issue could be several things
Fuel cut off switch engaged
Faulty spark plugs
Sticking/faulty starter motor
Fuel filter blocked (common reason for non starting and doesent give a fault code).
Fuel pump faulty or faulty/loose wiring at pump
Unlikley to be anything to do with the ecu as it turns over and no fault codes.

Mar 23, 2015 | Vauxhall Cars & Trucks

1 Answer

I have replaced solenoid and starter and still starter makes noise but doesent engage the flywheel why


Sometimes the starter has to be shimmed to engage the ring gear of the flywheel

Mar 17, 2013 | Cars & Trucks

1 Answer

Manual transmission wont take gear


check the properler shaft when gear is engaged if its rotating if not the problem is on clutch plate if it rotating and the car is not mocing check on the drive members

Feb 26, 2013 | Cars & Trucks

1 Answer

My 2000 dodge durago 5.2 starts right up but will not go into any gears or reverse. does this only mean my transmission is dead?


is you 2000 dodge manual or automatic gearbox?
manual: check on the properler shaft if its working while gear is engaged then selectors of a gear lever must be in correct possition
automatic: check on transmition oil filter and oil if in good condition

Jan 26, 2013 | Cars & Trucks

1 Answer

1999 ford taurus overheats boils out of res.new thermostat...saw water pumping 2 water pump....saw water pumping out of thermostat....not sure though seems like not enough water pumping through...


It sounds like you have an air pocket in your system. By the RH strut tower take the heater hose loose from the metal line and fill the cooling system when coolant starts coming out reconnect the hose. If that doesn't work jack the car up where the over flow tank is the highest point and fill the cooling system.

Sep 22, 2010 | 1999 Ford Taurus

1 Answer

I have a maytag over capacity plus heavy duty 2 speed 10 cycle washer it fills with water fine you hear the motor kick in to girate but doesent spin or you put it on spin cycle it sounds like it is...


The motor is working, but the mechanism not engaged by the helix so the shaft can not move therefore no agitation or spinning. Motor is designed to turn 2 directions: clockwise and counterclockwise for agitation and spinning. Therefore there are 2 mechanisms to assist these tasks. The drain is control by a separate pump and it is still good also.
The tube has to be out to replace the helix for agitation and a part to engage with the spinning rotation to release the brake so the spinning function can work. These parts are cheap, but the the labor is not. Hope this can help

Jan 09, 2010 | Washing Machines

2 Answers

How to troubleshoot automatic transmission of my isuzu automatic transmission


check the fluid. if your having issues thats about all you can do. This is when experience will be able to recommend a fix.

Nov 08, 2009 | 1992 Isuzu Trooper

1 Answer

Cant receive faxes


plz check all cables properl there might be damaged one ... then check you fax machine ink ..if none seems to be the problem the get it once serviced it will get back on working

Aug 27, 2009 | Canon PIXMA MP530 All-In-One InkJet...

2 Answers

How to start Mercedes C180 1999? Is it button start or key start?


i have a c180 merc petrol when starting the starter dosnt engage prop for afew turns then it engages and engine starts i have change the ring gear plus change the starter and still geting the same prob

Jun 28, 2009 | 1999 Mercedes-Benz C-Class

Not finding what you are looking for?
2006 Derbi GP1 125 Logo

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Derbi Experts

yadayada
yadayada

Level 3 Expert

66126 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

ARNE ERIKSSON

Level 2 Expert

204 Answers

Are you a Derbi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...