Question about 1994 Ducati 916

1 Answer

1998 916 ducati wont start on buton but starts when you run it off have good battery and new solonoid just wont turn over just clicks at solonoid

Posted by on

  • m_e_lambert0 Jan 05, 2009

    thanks it was the battery great advice thanks

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Either you have a bad battery(bad cell) or you need to clean you battery terminals.  Clean both end of the positive and negative cables.  If these are dirty or corroded  it will act like a bad battery.  Do this first since it is a free to do, plus it may save you from future problems.  Then before you buy a new battery, see if jumping it.  If it starts then you need a new battery.

Posted on Jan 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hello, I have a 2003 dr650se and it wont start using the electric start. it will bump start and run fine until you kill the motor then it wont start it just clicks. the battery is fine. is there a cut


I think your bike has 2 anti start switches the side stand and the clutch lever. You state it bump starts runs fine then clicks when you try to restart. The clicking is the starter solenoid which would indicate the battery has not enough cranking power to turn the starter motor. Check battery voltage must be above 12.5. remove battery (undo negative lead first). Wire a 21 watt bulb to the battery and see if it dims within a small period of time. If it remains bright try charging the battery only use a dedicated bike charger (less than 1 amp out put). Do not use a car charger ever. When the battery is fully charged refit to bike (refit positive lead first). Try to start the bike again. If it fails to start bump start it and check the voltage across the battery is should be about 14 to 14.5 volts. If low volts at the battery with the engine running your charging circuit is not working correctly. If the volts are good I would try another battery. They sometimes give false reading to chargers when a cell or 2 short out.

Sep 30, 2014 | 2012 Suzuki DR 650SE

1 Answer

The starter switch doesn't do anything and I have a fault code on the dash that says start error 19.2 I've disconnected side stand switch but it starts if you make contact on the starter


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have nice a day.
Bike wont turn over Tried recharging battery and then new one too Clicking...
Bike will not start Please help me out ducati org forum the home for.
DOWNLOAD 2008 Ducati 1098
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance

Jan 12, 2014 | 2008 Ducati 1098

1 Answer

Ducati monster wont start


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have nice a day.
2005 Ducati Monster 620 Wont Start
http://www.ducatimonster.org/forums/tech/205386-2006-monster-620-wont-start-just-clicks-when-i-press-start.html
2004 2006 Ducati Monster 400 620 Motorcycles Service Repair Manual Highly...
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance

Dec 20, 2012 | 2002 Ducati Monster 620s i.e.

1 Answer

Ducati 620 wont start with new battery


Hi, Efrensaunder and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have nice a day.
http://www.ducatimonster.org/forums/tech/205386-2006-monster-620-wont-start-just-clicks-when-i-press-start.html
Monster 620ie not starting help Ducati DUCATI 620 MANUAL SERVICE REPAIR FSM 2002 2006 DOWNLOAD Download Manuals...
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance

Jun 12, 2012 | 2003 Ducati Monster 620s i.e.

1 Answer

Will not start from the button


Hi, Bob and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have nice a day.
Bike wont turn over Tried recharging battery and then new one too Clicking...
Bike will not start Please help me out ducati org forum the home for...
DOWNLOAD 2004 Ducati St3
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance

Jan 11, 2012 | 2004 Ducati ST3

1 Answer

Just bought a 2007 ducati monster s4r with 1749 miles that seemed to run fine until after a couple hour ride. the next day, the oil light and maintenance warning came on it but started, then suddenly shut...


Hi, Mr_sixtomerc and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have nice a day.
Bike wont turn over Tried recharging battery and then new one too Clicking...
Ducati Monster won start fixed see how
Ducati Monster S4R 2003 2006 Factory Service Repair Manual Download...
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance

Apr 21, 2011 | 2007 Ducati Monster S4R Testastretta

1 Answer

Starting problem ducati already replaced starter solinoid starter switch and new battery still wont start


Hi, Leo and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
8. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
10. Ignition timing incorrect due to a faulty ignition coil, ignition module or sensors (MAP, CMP, CKP, O2 and/or BAS).
11. Security alarm needs a reset.
For more information about your issue and free downloads that you will need please visit the websites below. Good luck and have a nice day.
Bike has trouble starting Won turn over clicks sometimes Bad battery...
Still won start Ducati ms The Ultimate Ducati Forum
Free Ducati Motorcycle Service Manuals for download
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance

Apr 17, 2011 | 2002 Ducati 750 Sport

1 Answer

I have a Riding mower Sears Model 917275660 with a Kohler Engine Model Number SV600, Type number 0001. The engine will not start. I have a new Battery but when I try to start the only thing I hear is the...


So the engine wont turn over at all? Well, we know the fuse is good since the fuel solonoid is getting power. Do you have a test light? Locate the starter solonoid, check for power to the small spade on the starter solonoid when the key is turned to the start position. Be sure the brake pedal is depressed, the pto is disengaged, and that the seat switch is depressed.
If you have power to the small spade then check the large posts for power. The battery side should have power all the time and the starter side should have power when key is turned to start. If you have power from battery and power from key switch but no power to starter then the starter solonoid is suspect.
If solonoid tests good and power is getting to starter but starter doesnt engage then starter is suspect.
If no power to small spade on starter solonoid then you will have to do some back tracking. It could be the key switch, one or more of 3 safety switches or bad wire/ bad connections

Dec 07, 2009 | Craftsman Garden

2 Answers

Pontoon wont start.The starter is good the cylonoid is good.the starter will come up and start to turn the flywheel and stop.I can hear the starter whine.but wont turn over.I have charged the new battery.


I have worked on many outboard motors. Since your motor almost starts, do these things:

1. install new spark plugs unless you are certain that the ones u are using are good.
2. Add a product called seafoam to the gas tank. Check to be sure but I recall that you add one ounce per gallon [this stuff is great].
3. At any auto parts store get a can of electrical connection spray. Spray all of your contact points.
4. Also get a can of starter fluid. Give the air intake a couple of short blasts and start the motor. if it runs real rough continue with the startere fluid until it runs smoothly.
5. Be sure that your battery cables are corrosion free where they slide over the battery terminals and that the connections are tight.

Enjoy your boat ride.

Sep 07, 2009 | Sport & Outdoor - Others

1 Answer

Ducati 748 2001 Reg. Problems with starting Bike. Turning on the ignition and completely dead !!!!! When you turn the ignition off.....the red immobilisor flashes once. Have checked and reset Alarm...


Hi, Sarah_in_flo and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have nice a day.
2005 Ducati Monster 620 Wont Start
http://www.ducatimonster.org/forums/tech/205386-2006-monster-620-wont-start-just-clicks-when-i-press-start.html
Ducati 748 1993 2004 Workshop Repair Service Manual PDF Download Manuals...
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance

Apr 26, 2009 | 2004 Ducati Monster 620 Capirossi

Not finding what you are looking for?
1994 Ducati 916 Logo

Related Topics:

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ducati Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

bobkoure

Level 1 Expert

36 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Ducati Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...