Question about 2002 Yamaha YZ 426 F

1 Answer

High beam warning light

High,i have a tzr125 belgardo the high beam warning light is on even when on low beam all the wiring looks ok or could the fault be in the mag,i have spent a lot of time on it but not found the fault,any suggestions

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 137 Answers

Hey dude,, just to try n help the easiest way,, on the hi beam lite u will only have two wires on some bikes ,but 3 wires mostly runnin into it,, so 4 an example lets say u got 2 wires,,this being yellow and green if i remeber,,yellow will be hi beam ,,green is low,, the earth would come from the bulb and earth in to the loom,, ,, easiest thing to try,, and by pass hassle,, is on the hi beam lite itl be the yellow wire ie the live on that bulb ,snip it off enuff to be able to join it to the hi beam on the bulb in the head lite, , ,, so u have in your hand say u have the hi beam lite which will have an earth wire black,, leave that connected,, and a yellow wire ,which will be the live in,,snip that wire and touch it on the yellow on the headlite bulb ,, dip the lite and hi beam will go out,,hope that helps

Posted on Jan 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High beam do not work at all low beam works fine when switched to high beam no lights at all


I suggest you first check the bulbs. It isn't unusual that both bulbs fail together.
If the bulbs are ok refer to the vehicle handbook and check the fuse(s).

If those are ok it is time to move onto the supply and check it through with the aid of a wiring diagram. The fault could be a relay or the dipswitch, wiring, connections...

It is worth noting on later vehicles electrical equipment is not switched on with the light, wiper, heater switches but these merely instruct a local black box to send a signal to other black boxes to perform the desired function. In the case of problems a dedicated scan tool will be required for diagnosis.

Aug 10, 2015 | Cars & Trucks

1 Answer

High beams work for both lights, 1 low beam does not


Check for power with a test light with the light connected. If you have power then its the ground. If no power then you will need to trace the wire back to find break. As I recall they did have seperate fuse for left and right headlight high & low beam. Also did you get a defective new bulb?

May 31, 2015 | 2006 Mazda Tribute

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

Replace headlight relays 1999 lexus rx300


Moe likely a bad earth for one of the lights as one light is working through another causing one to stop working

Feb 06, 2013 | 1999 Lexus RX 300

1 Answer

My high and low beams were off, then i cleaned the corrosion off the connector of the battery and now the high beams work...low beams still do not! 2005 hyundai sonata


battery acid may have gone down the side and eaten-through some wiring.....happened to me once, though the car was 12+years old at the time. Took-out most of the electrical stuff in the car w/o warning....

Tallon41

Sep 11, 2012 | Hyundai Sonata Cars & Trucks

2 Answers

2005 Ford Focus ZX3 SES, the blue high beam indicator in the dash comes on with low beams, and goes off with high beams. The indicator is on at the wrong time! I have tried the following: The turn signal...


It sounds like you are confused about how your headlamp system is supposed to work. The DRL does not run on the High beam circuit, it runs on the low beam circuit. The fog lamps are supposed operate with the park lamps and also with the low beams, not the high beams. From your description, I would say that your system is operating as designed and you are having trouble telling High from Low. (Don't feel bad, that is why high beam indicators were invented in the first place.)

May 08, 2011 | 2005 Ford Focus

1 Answer

Low Beam headlights don't work. High Beam work fine and diriving lights work as well.


hi from uk provided you have checked bulbs are ok? then this fault may be the relay for the low /dipped beam has gone faulty if you check h/book you may find location of low beam relay there is relay for high and one for low beams if you find both relays ? try switching? this will confirm relay fault if you then have low beam but no high ? b4 you buy new relay other than tis the other possible fault may be the actual di/high beam stick control ?

Nov 09, 2009 | 1998 GMC Sierra

1 Answer

High Beam Wire Color? Distinction between three?


with a test light ground connected to the positive battery terminal,,the one that will light up the light is the ground...the other 2 wires are the low and high beam. cut one of those,if the low beam is now on,you cut the high beam wire. if the high beam stays on,you cut the low beam wire.

Jul 22, 2009 | 1991 Toyota Tercel

1 Answer

Low beams suddenly stopped working -1988 Volvo 760 GLE


I doubt that the obc is the source of the problem.
More than likely, it's the relays.
They're not easy to remove, until you remove the ashtray housing, which is 4 fixings in total, if I recall correctly.
Good luck.

Jul 13, 2009 | 1997 Volvo 960

1 Answer

Is there a drain plug for the water pump on a 2000 yz 426f. I want to drain the system, and change it to engine ice. I don't know if there is a plug or if you have to take the pump off


I have a tzr 125 belgado the high beam warning light is on even when i have low beam on could the fault be in the mag or the wiring,thanks dave

Jan 01, 2009 | 2002 Yamaha YZ 426 F

Not finding what you are looking for?
2002 Yamaha YZ 426 F Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...