Question about 1978 Yamaha RD 250

1 Answer

Are rd250 muffs the same as 350rd mufflers?

Purchased a 1970 rd 250. Bike came with a extra set of pipes from a 350rd. These muffs are in great condition compared to the ones on my bike. Pipes look the same. Will these pipes bolt up and perform as stock replacements?
Thank you
Raoul

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

No - the are close - but allow more air flow and less back pressure (very important)

Posted on Dec 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What oil is recommended for the oil tank in a 1974 yamaha rd250?


The 1974 RD 250 has a two cycle engine. The oil tank is for engine oil injection. You will use a good quality 2 cycle engine oil that is recommended for oil injection. Fill the tank and remember as you drive the level will go down, so keep an eye on it. If the tank runs out of oil you will ruin the engine. Also there is oil in the clutch/transmission case. There should be a site glass or dipstick attached to the filler plug. After you remove it do not screw it in to check the level (make sure the bike is sitting level). This is a different type of oil as well. I hope this helps! Rod

Aug 12, 2015 | Yamaha Motorcycles

1 Answer

I may buy a 1976 Yamaha RD400. Has sat for about 10-15 years. What should I look for to tell if it's got any value or if it's a boat anchor? I'm first check kick start for turn over, gas tank...


Hi,,,the major things,as it has sat for so long will be,,gummed up carbs,,hardened crank seals and rust in the tank..

You can jump start it but i dont reccomend it.

Price will vary with condition,,both external and engine wise.

They are a great bike,,,good luck with it.

Aug 03, 2011 | Yamaha RD 250 Motorcycles

1 Answer

Can i fit the top end of 1977 rd400 on the bottom end of a 1974 rd250?


I know the rd250 and rd350 interchange. The rd400 cylinder base gaskets are the same as the 250 and 350. You just need to know if they have the same crankshaft stroke is the same and the if the piston pins are the same diameter(they are also a different pn#).

Oct 02, 2010 | 1974 Yamaha RD 250

1 Answer

Please forward me the wiring diagram of the 1974 Yamaha RD250 as the wiring of my bike needs to be attended.


Go to the site below and you can free download an Owner's manual. There is a 1976 model manual there that will have the same wiring harness. Cheers!

http://www.yamahaownershandbook.com.au/index.php

Sep 02, 2010 | 1974 Yamaha RD 250

1 Answer

What kind of battery does the 74 rd250 take and how much does it cost


What is this ... call motorcycle shop and ask them. This is a simple thing to do.

Oct 01, 2009 | 1974 Yamaha RD 250

1 Answer

To mitigate the exhaust Aquila 250


exaust silencers or 'mufflers' as we call them in the US could be purchased at a motorcycle parts supplier.measure the outside diameter of your exhaust pipes to determine the proper size ''slip on'' mufflers you need to buy & clamp onto pipes.if you can't find them locally,visit www.jcwhitney.com/motorcycle

Sep 27, 2009 | 2001 Hyosung GV 250 Aquila

2 Answers

07 kawasaki kx250f backfires


Hey i have several solutions for you.
The first is have you checked valvue clearence lately, because if the valvue clearence is either to high or to low then it could cause it to back fire. The next solution is repacking your silencer. The next solution is there is two main gaskets in most dirtbikes, one, which is located where the pipe mets the motor. Also the other gasket it where the mid pipe meets the head pipe. The bike fire is usually being caused by extra air. By the way checkin valvue clearence is extremley easy it may sound hard but I do after every ride.

Jun 08, 2009 | 2006 kawasaki KX 250 F

1 Answer

How to reassemble header for 2002 Kawasaki Ninja 250


first lay out all your exhaust system parts . take inventory.2 ex. gskt.2 mffler gskt,left muffler(short),right muffler(long), header pipe,4 collars, 4 nuts(6 mm),2 holders,2 muffler clamp,2 hanger bolt,2 nut( 10 mm). next. put small dab of grease on exhaust donut gaskets so they will stay in place by themselves when you stick them in place in the exhaust ports ,on the cyl. head.next gather collars, head pipe w/ holders & 6mm nuts, w / 10mm .wrench or socket.tricky part,hold head pipe up in plce to head,take collars w/ lip or bend facing out & put in between pipe holders & ex. donut gaskets,place holders over exhaust studs & install 6 mm nuts & tighten evenly but do not tighten all the way just keeping collars in place. now hang mufflers,w/ gaskets,clamps,nuts, & bolts,loosely.now tghten down head pipe evenly,cheking collars for proper alignment as you tighten.next,tighten mufflers to headpipe w/ clamps using 12 mm socket or wrench.next, tighten mufflers to frame using 14 mm.finally, start bike & check for exhaust leaks.

Feb 14, 2009 | kawasaki Ninja 250R Motorcycles

Not finding what you are looking for?
1978 Yamaha RD 250 Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

D. E. Hev

Level 3 Expert

1059 Answers

mikeuk

Level 2 Expert

61 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...