I need to remove front wheel

How to install quick release front wheel on bicycle - YouTube

? 0:58
https://www.youtube.com/watch?v=xFx7UXyjW4Y
Dec 11, 2011 - Uploaded by Bicycles Online
When I went to reinstall my wheel my brake pads were stuck together and I don't know how to get them apart ...

How To Remove The Front Wheel of a Bicycle - YouTube

? 7:31
https://www.youtube.com/watch?v=BNwa0lONtbc
Jun 30, 2012 - Uploaded by cjhoyle
This is a quick tutorial showing how to remove the front wheel of a bike. ... Getting the lightly tightened other nut off shouldn't be aproblem.

Removing and installing your bicycle wheels - YouTube

? 4:06
https://www.youtube.com/watch?v=QslgCn9QX5I

to remove front axle.to loosen front axle nut leave vechicle weight on wheel then just loosen front axle nut because axle nut torque at 217 ft lbs torquehard to loose axle nut with vechicle weight off wheel.okay. you need a 1/2 breaker bar and axle socket to loosen axle nut dont use 12 points sockets need go auto parts store buy right socket for axle nut.okay when you loosen front axle nut you need safely raise support vechicle. need to remove wheels remove fender apron seal remove transaxle fluid remove transfercase oil if you have 4WD.remove hub nut remove stabilizer bar link remove speed sensor remove tie rod end remove lower arm from the ball joint then slide the halfshaft from the hub then carefully pry the shaft from the transaxle.then install new front axle push in make sure front axle snap ring on front axle snap in place inside transmission just pull a little on front axle make its in place. when all done tighten front axle much as you can then when done putting every thing back in place.lower vechicle need torque front axle nut to 217 ft lbs.

Wheel Spindle, F-150, F-250, F-350
Removal

1. Raise the front of the vehicle and install safety stands.
   

1. Remove the wheel and tire assembly. Refer to Section 04-04 .
   

1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
   

1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
   

1. Remove the rotor from the front wheel spindle (3105).
   
   
   
   
   
   Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
   (57-75 Lb-Ft) B - Tighten to 68-92 Nm
   (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)

1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
   

1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
   

1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
   

1. Remove the cotter pin and castellated nut from the lower ball joint stud.
   

1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
   

1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
   

1. CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
   Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
   

1. Remove the front wheel spindle and ball joint from the axle.
   
   

Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal

1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
   

1. NOTE: Lower ball joint must be removed first.
   
   Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
   

1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
   

1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
   
2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
   Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.
   
   
   Installation
   
   1. CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.
      
      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.
      
      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
      
   1. Turn forcing screw clockwise until ball joint is seated.
      
      
      
      
   

To do this safely and securely you will need to obtain a front paddock stand which supports your front wheel, you will then need a "24mm hex drive socket" to loosen the wheel, pull the spindle out and wheel shoul slide out easily.

it just pulls out. it hasa circlip that holds it in on driver side. which side?

here's an escort, should be similar. note step 17

Removal

1. Raise and support the vehicle.
   

1. Remove the lug nuts (1012) and the front wheel and tire assembly.
   

1. Remove the front fender splash shield bolts and the front fender splash shields (16103) .
   

1. Use a small cape chisel to carefully raise the staked portion of the front axle wheel hub retainer (3B477).
   
   
   
   
   

1. Remove the front axle wheel hub retainer and discard it.
   

1. Remove the cotter pin and the tie rod end nut from the tie rod end (3A130). Discard the cotter pin.
   
   
   
   
   

1. Use an appropriate tie rod end remover to separate the tie rod end from the front wheel knuckle (3K186).
   
   
   
   
   

1. Remove the ball joint bolt and the ball joint bolt nut.
   
   
   
   
   

1. Carefully pry down on the front suspension lower arm (3078) to separate the front suspension lower arm ball joint (3050) from the front wheel knuckle.
   
   
   
   
   

1. Pull outward on the front wheel knuckle (3K185). Carefully pull the front wheel driveshaft and joint from the front wheel knuckle and position it aside.
   
   
   
   
   

1. NOTE: Removal of the LH front wheel driveshaft and joint (3B437) requires removal of the transmission support crossmember (6A023) to allow access with a pry bar. If the LH front wheel driveshaft and joint is being removed, continue with step 11. If the RH front wheel driveshaft and joint is being removed, continue with step 15.
   
   Support the transaxle with a transaxle jack or equivalent.
   

1. Remove the four transaxle mount-to-rear engine support nuts.
   
   
   
   
   

1. Remove the two rear engine support nuts at the rear of the transmission support crossmember.
   

1. While supporting the rear of the transmission support crossmember remove the two rear engine support bolts. Remove the transmission support crossmember.
   
   
   
   
   

1. Position a drain pan under the transaxle.
   

1. Insert a pry bar between the front wheel driveshaft and joint and the transaxle case.
   

1. CAUTION: Extreme care must be taken to ensure that the pry bar does not damage the transaxle case, the transaxle oil seal, the front wheel driveshaft and joint, or the front wheel driveshaft joint boot (3A331).
   Gently pry outward to release the front wheel driveshaft and joint from the differential side gears (4236).
   
   
   
   
   

1. Remove the front wheel driveshaft and joint.
   
   
   
   
   

1. CAUTION: When the LH and RH front wheel driveshaft and joint assemblies are removed, Transaxle Plugs T88C-7025-AH must be inserted to prevent the differential side gears from becoming mispositioned. If the gears become misaligned, the differential will have to be removed from the transaxle to align the gears.
   If both front wheel driveshaft and joints were removed, install Transaxle Plugs T88C-7025-AH in the differential side gears.
   

1. Remove and discard the driveshaft bearing retainer circlip (3Z498).
   

There are no front wheel drive rodeos but there are 4 wheel drive and all wheel drive. If it is not 4 or all wheel drive then there is no front shafts. You will need to remove the rear drive shaft though to remove the transmission. Hope this helps. Good luck.

Hub and Bearing Assembly
CAUTION: Do not begin this removal procedure unless the following parts are available:

• A new front axle wheel hub retainer (3B477) (Step 1).
• A new inboard halfshaft joint stub shaft circlip.

Once removed, these parts must not be reused during assembly. Their torque holding ability or retention capability is diminished during removal.
Removal

1. Turn ignition switch to the OFF position and place the steering column in the unlock position.
   

1. CAUTION: Discard the front axle wheel hub retainer. It is a torque prevailing design and cannot be reused. If loosened, the retainer must be removed and a new one installed.
   Remove and discard front axle wheel hub retainer (3B477).
   

1. Raise vehicle on hoist.
   

1. NOTE: Make sure steering column is in the unlocked position, and do not use a hammer to separate tie rod end (3A130) from the front wheel knuckle (3K185) . Use extreme care not to damage boot seal.
   
   Remove cotter pin from tie rod end stud and remove slotted nut. Discard cotter pin and nut.
   

1. Using Tie Rod End Remover 211-001 (TOOL-3290-D) or equivalent and Tie Rod End Remover Adapter 211-087 (T81P-3504-W), remove tie rod end from front wheel knuckle.
   

1. CAUTION: Use extreme care not to damage boot seal. Do not use power tools to remove the nut, or bearing and seal damage will result. Loosen the nut first, then remove nut from stud using the hex hold feature.
   For SHO vehicles, remove vinyl cover from upper link stud.
   Remove stabilizer bar link (5K484) from front shock absorber (18124) .
   

1. Remove disc brake caliper (2B120) and support with wire to obtain working space. Do not allow disc brake caliper to separate from the front disc brake caliper anchor plate (2B292) to prevent contamination of the disc brake guide pin journals. Do not allow disc brake caliper to hang from front brake hose (2078) . Remove front disc brake rotor (1125) . Remove front disc brake rotor from wheel hub (1104) by pulling it off the lug bolt (1107). If front disc brake rotor is difficult to remove from front wheel knuckle , strike front disc brake rotor sharply between lug bolt with a rubber or plastic hammer.
   If front disc brake rotor will not pull off, apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to inboard and outboard rotor/hub mating surfaces. Install 3-Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor by pulling on front disc brake rotor outside diameter and pushing on hub center. If excessive force is required for removal, check front disc brake rotor for lateral runout prior to installation. Refer to Section 06-00.
   

1. Remove anti-lock brake sensor mounting bolt and front brake anti-lock sensor (2C204) .
   

1. Remove and discard lower ball joint nut. Using Remover Adapter 211-211 (T96P-3010-A1), separate lower ball joint from front suspension lower arm (3078) .
   

1. Using Rotunda Spring Compressor 014-00781 or equivalent, compress front coil spring (5310) until lower ball joint clears front suspension lower arm .
   

1. Using Front Hub Remover/Replacer 204-069 (T81P-1104-C), Two Stud Adapter 205-237 (T86P-1104-A1), Metric Hub Remover Adapter 204-085 (T83P-1104-BH) and Front Hub Installer 204-067 (T81P-1104-A), press front wheel driveshaft joint (3B414) from wheel hub . Wire front wheel driveshaft joint to body to maintain a level position.
   
   
   
   
   
   Item Part Number Description 1 204-085 (T83P-1104-BH) Metric Hub Remover Adapter 2 204-067 (T81P-1104-A) Front Hub Replacer 3 — Turn Wrench Counterclockwise 4 — Hold Wrench Stationary While Turning Other Wrench 5 204-069 (T81P-1104-C) Front Hub Remover/Replacer 6 204-067 (T81P-1104-A)1 Two Stud Adapter A — Make Sure Metric Hub Remover Adapter 204-085 (T83P-1104-BH) is Fully Threaded onto 1107 and is Positioned Opposite the Two Stud Adapter 205-237 (T86P-1104-A1)

1. Remove and discard three hub and bearing retainer bolts from front wheel knuckle .
   

1. NOTE: Wheel hub is not pressed into front wheel knuckle . Do not use slide hammer to remove a stuck wheel hub . Do not strike back of inner bearing race. Use of these methods will damage bearing internal parts.
   
   NOTE: If bearing carrier is corroded to front wheel knuckle , apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to the inboard and outboard wheel hub/knuckle mating surface and allow to soak.
   
   Remove wheel hub from front wheel knuckle .
   
   
   
   
   

Installation

1. NOTE: If wheel hub is damaged or if any end play is detectable, replace wheel hub . End play is not adjustable. If wheel hub is disassembled, the assembly must be replaced.
   
   Remove all foreign material from knuckle bearing bore for correct seating of new wheel hub.
   

1. Lightly lubricate mating surfaces of bearing corner and front wheel knuckle.
   

1. CAUTION: Knuckle bore must be clean enough to allow wheel hub to be completely seated by hand. Do not press or draw wheel hub into place.
   Position wheel hub in front wheel knuckle . Install three new hub and bearing retaining bolts. Tighten to 83-107 Nm (61-78 lb-ft).
   

1. Push front wheel driveshaft joint into wheel hub . Hand start front wheel hub retainer.
   

1. Slowly release Rotunda Spring Compressor 014-00781 or equivalent while guiding lower ball joint into front suspension lower arm .
   

1. Install new lower ball joint nut. Tighten to 68-92 Nm (50-67 lb-ft).
   

1. Install tie rod end into front wheel knuckle . Install new slotted nut and tighten to 47-63 Nm (35-46 lb-ft). If necessary advance nut to install a new cotter pin.
   

1. CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
   Install stabilizer bar link to front shock absorber . Install stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft). For SHO vehicles, install stud cover.
   

1. NOTE: Remove rust from the rotor and hub mating surfaces with a medium abrasive pad.
   
   Install front disc brake rotor and disc brake caliper . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
   

1. CAUTION: The front axle wheel hub retainer must be tightened to specification immediately during installation. If the retainer is not tightened immediately, the nylon lock will set incorrectly, leading to incorrect torque readings and bearing failure. Any front wheel hub retainer that is not immediately tightened to specification or is loosened must be removed and a new retainer installed.
   Install front axle wheel hub retainer . Tighten to 230-275 Nm (170-203 lb-ft).
   

1. Install wheel and tire. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
   

1. Lower vehicle.
   

1. Pump brake pedal prior to moving vehicle to position brake linings.
   

here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal

1. Raise vehicle on hoist.
   

1. Remove wheel and tire assembly. Refer to Section 04-04 .
   

1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
   

Brake Shoe and Lining Removal

1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
   

1. Raise vehicle on hoist. Refer to Section 00-02 .
   

1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
   

1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
   

1. NOTE: It is not necessary to disconnect hydraulic connections.
   
   Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
   

1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
   

1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
   

1. Remove inner brake shoe and lining assembly.
   

1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
   

1. Remove lug bolt from wheel hub (1104).
   
   
   
   

Installation

1. Install lug bolt into wheel hub.
   

1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
   

1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
   

1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).
   

http://groups.yahoo.com/group/villagerquest/


Item Part Number Description 1 — Cotter Pin 2 — Nut Retainer 3 1131 Insulator 4 3B477 Front Axle Wheel Hub Retainer 5 1195 Front Wheel Outer Bearing Retainer Washer 6 1104 Wheel Hub 7 1107 Lug Bolt 8 3K050 Snap Ring 9 3123 Front Wheel Bearing 10 2K004 Front Disc Brake Rotor Shield 11 3130 Front Wheel Knuckle

Wheel Hub, Wheel Knuckle and Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Tie Rod End Separator T85M-3395-A
Removal

1. Raise and support the vehicle.
   
2. Remove the wheel (1007) and tire assembly.
   
3. NOTE: It is not necessary to disconnect the front brake hose (2078).
   
   Remove the disc brake caliper (2B120) and suspend it with mechanic's wire out of the way. Refer to Section 06-03 for the removal procedure.
   
4. Remove the front disc brake rotor (1125).
   
5. Remove and discard the cotter pin.
   
6. Remove the nut retainer and insulator.
   
7. Remove the front axle wheel hub retainer (3B477) and the front wheel outer bearing retainer washer (1195).
   
   
   
   
   
8. Remove and discard the cotter pin from the front suspension lower arm ball joint (3050).
   
9. Loosen the front suspension lower arm ball joint nut until it contacts the front wheel driveshaft joint.
   
   
   
   
   
10. Strike the front wheel knuckle with a hammer while pulling down on the front suspension lower arm (3078) until the front suspension lower arm ball joint separates from the front wheel knuckle.
    
    
    
    
    
11. Remove the front suspension lower arm ball joint nut.
    
    
    
    
    
12. Remove the front suspension lower arm ball joint from the front wheel knuckle.
    
13. Remove and discard the cotter pin.
    
    
    
    
    
14. Remove the tie rod end nut.
    
    
    
    
    
15. Use Tie Rod End Separator T85M-3395-A to separate the tie rod end (3A130) from the front wheel knuckle.
    
    
    
    
    
16. Remove the front brake anti-lock sensor bolt.
    
    
    
    
    
17. Remove the two front shock absorber-to-front wheel knuckle nuts.
    
    
    
    
    
18. Remove the two front shock absorber-to-front wheel knuckle bolts.
    
19. Remove the front shock absorber (18124) from the front wheel knuckle.
    
20. Use 2-Jaw Puller D80L-1002-L, or equivalent, to separate the front wheel driveshaft and joint (3B436) from the front wheel knuckle.
    
21. Remove the front wheel hub, front wheel knuckle and front wheel bearing as an assembly from the vehicle.
22. If necessary, match mark and remove the steering stop bolt and steering stop bolt jam nut from the front wheel knuckle.
    
    
    
    
    

Installation

1. Position the front wheel hub, front wheel knuckle and front wheel bearing as an assembly on the front wheel driveshaft and joint.
   

1. Install the front wheel knuckle into the front shock absorber.
   

1. Install the two front shock absorber-to-front wheel knuckle bolts.
   

1. Install the two front shock absorber-to-front wheel knuckle nuts. Tighten the front shock absorber-to-front wheel knuckle nuts to 113-123 Nm (83-91 lb-ft).