Question about 2005 Honda CB 250 Nighthawk

1 Answer

1992 Honda 250 Nighthawk Handle bar diammeter

Am trying to add a wind shield and need to know the diameter of the handle bars to order.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,692 Answers

Take an ajustable wrench and place it around the handlebar where their is a straight section, snugly. Slide the wrench off without ajusting it. Measure with a ruler or tape measure the distance between the wrench jaws. That measurement is the diamater of your handle bars.

Posted on Dec 22, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Honda motorcycle

Check the clutch adjustment it may be not disengaging properly & you may need to wind out the outer cable on the handle bar left side

Jul 20, 2014 | Honda XL 125 V Varadero Motorcycles

1 Answer


There is a line that goes up through handle bar to feed clutch fluid and choke on bars, sounds like it is pinching it when turning trace lines and make sure enough slack and no pinch lines. Please let me know results, thanks . Mike

Jun 06, 2011 | 2009 KTM 250 SXF

1 Answer

Hi i would like to know how to add water for the honda goldwing 1500 gl i want to know what to remove to find the place were to add water

Sit on the bike and turn the handle bars to the right. Look on the left hand side where the left handle bar was and you will see a rubber cap. Remove the left plastic cover panel around it and remove the rubber cap. It has hash marks to measure by. Ad 50/50 antifreeze till you see it half way up the hash marks. Be sure the rubber cap snaps back on tightly all the way around.If you ever need access to the radiator cap it is on the right side under that plactic cover. But you can add coolant on the left side. This is the upper level resivoir.

Sep 03, 2010 | 1990 Honda GL 1500 Gold Wing

1 Answer


Dot 3/4 brake fluid is added to the clutch master cylinder on the left handle bar. The left (clutch) handle bar lever is attached to the clutch master cylinder. To add fluid you will have to remove the phillips screws (4 x 12 oval screws) holding the cover on. Be sure to lay plastic over the motorcycle (with a towel or rags over that) to protect the bikes plastic and paint from any DOT 3/4 fluid you may spill during the filling or bleeding process. Caution: brake fluid will brittle and crack expensive Honda plastic.

Aug 25, 2010 | 1985 Honda GL 1200 Interstate Gold Wing

2 Answers

1991 CB 250 Nighthawk: whats the top speed for a 1991 honda nighthawk 250...

I have had my 2008 Nighthawk 250 up to 70mph with some left over. I just got it so I haven't really run it full throttle yet ( 75 miles on the OD ) I weight 300 lbs. I would guess 80 on a flat road. I felt comfy at 70 but this is my 5th bike. I bought this one for the gas mileage and 1 yr. warranty. I will try actual top speed on the Interstate in about 1000 miles. Hope this helps. I like the bike. Chris

May 17, 2010 | 1991 Honda CB 250 Nighthawk

1 Answer

Got a sticky throttle on a honda CBR 250 rr how can i fix it

start at the handlebar end. loosen the 2 screws and slide off the throttle from the handle bar, wipe down the handle bar, and put a thin film of grease on it, then slide it back on, being sure not to slide it on all the way, about 1mm back, to prevent the handlegrip rubbing on the end of the bar. Next you need to lubricate the cable, this is best done from the top handlebar end, you need to take apart the cable housing, so you can spray some thin lubricant down the cable, such as WD-40, or you can even buy special cable lube. This will fix your problem im sure.

May 13, 2010 | 2002 Honda CR 250 R

1 Answer

1992 honda nighthawk 750 wont stay on and when i rev the gas handle, it turns off. do i need to change the fuel filter or jett the carbs?

sounds like you have to clean out the carbys. you should be able to at least drain them without taking them apart.

May 09, 2010 | 1992 Honda CB 750 Nighthawk

1 Answer

I need to know what size my handle bars are for the honda shadow vt750dca. 7/8ths or 1"? Anyone know?

use a tape measure and measure the bar width it will be one of the two?its the best way to get it right.

Feb 02, 2010 | 2005 Honda VT 750 DC Shadow Spirit

1 Answer


For more power you can port the engine but I would start with performance Reeds. Also would adjust suspention and revalve if needed. That would be it for me…,,

Nov 10, 2008 | 2003 HM CRE 250

Not finding what you are looking for?
2005 Honda CB 250 Nighthawk Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4497 Answers


Level 3 Expert

63661 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides