Question about Harley Davidson Honda Hunk 150 Motorcycles

1 Answer

2009 V-ROD MUSCLE WILL NOT START, TURN SIGNALS FLASH BACK AND FORTH 3 TIMES

My 2009 v-rod muscle will not start, it has power but the turn signals flash back and forth 3 times

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Harley Davidson Master
  • 57,416 Answers

Hi Rick, please visit websites below:
Disable the alarm 1130cc com The 1 Harley Davidson Rod Forum
rod alarm trouble help Harley Davidson Forums
Good luck

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Posted on May 03, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
wayneman01
  • 301 Answers

SOURCE: turn signals wont flash but somtimes,bulbs good

If they both come on, front and rear, but won't flash, then the most likely problem is the winker relay. When you flick the turn signal switch and they sometimes flash, that's because you're working the relay repeatedly and jarring it into action. Try a new realy (the box that makes them flash) and you should be fine.

Posted on Dec 13, 2009

Testimonial: "thanks,that fixed it."

  • 109 Answers

SOURCE: flashes turn signals 3 times quickly, will not

Sounds like alarm problem.Don't know why it starts cause anti theft part of system should shut down injectors?Anyway I think the 3 flashes tells you the system is armed so engine won't turn over.If you have remote key use that instead of key to shut off alarm after the flashing.NO go then wire around it and try starter.

Posted on Mar 20, 2010

  • 17 Answers

SOURCE: abs lights flash back and forth. They don't turn

Hi, you could try re-setting the abs. To do this you will need a length of 2amp cable about 500mm long, fix a small crocodile clip to one end, remove seat and search for a three pin blank connector, when you have located this put key in ignition but do not switch on at this point. Bare the end of the wire and insert in CENTRE hole of socket, put croc clip onto a good earth, then press abs button at the same time turn on ignition, count for 30 seconds, let go of abs button, switch off ignition, remove cable, put seat back on. This should reset abs. Sit back and have a beer. Cheers.

Posted on Aug 15, 2010

wd4ity
  • 4565 Answers

SOURCE: Battery is charged, but bike will not start. When

First, check the "Run/Stop" switch on the right handlebar switch housing. Make sure it's in the "Run" position. If it is, your starter relay may not be working. The relay is exactly like those on your car, a one inch plastic cube. Now, where it's located, I'm not sure. It could be under the seat or behind either of the two side covers on your bike. Once you find it, turn the switch on, hold on to the relay, and push the start button. You should feel the relay click. If it does click but the starter does not engage, you need to test the voltage coming out of the relay.

To test the output of the relay, look at the end of your starter from the right side of your bike. You'll see a five sided plate on the end of the starter solenoid. At the top of the plate, you'll see a single wire plugged into the starter. Unplug the wire and stick a test light probe in the connector on the end of the wire. Again, turn the switch on and press the start button. If the light lights up, your relay is good. If not, the relay is probably bad.

To do a final test on the starter, remove the five sided plate by removing the three small bolts that secure it. You'll see a plunger inside the solenoid. Make sure the bike's transmission is in neutral. Using a large screwdriver, push the plunger into the starter solenoid. The starter should engage and turn the engine over regardless of whether the switch is "on" or "off". Make certain that you push the plunger all the way in. If the starter does not turn, you starter is bad.

Good Luck
Steve

Posted on Nov 24, 2010

taran_2005
  • 10515 Answers

SOURCE: Where can I buy an owners manual for my HD V Rod

Hi,

You need to sign in or create a profile :

https://www.harley-davidson.com/en_US/Content/Pages/Owners/service-your-bike/owners-manuals/owners-manuals.html

You could access all the manual from their site.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Sep 01, 2011

Testimonial: "Thank you very much, this advice was for me very helpfull, thanks a lot"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 Harley Davidson VRSCF V-Rod Muscle tire pressure


Hi, Andrew for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Correct rear tire pressure for Rod Muscle Harley Davidson Forums
https://tirepressure.com/motorcycle/harley-davidson/vrscf-v-rod-muscle Recomended Tire Pressure on 2004 VROD 1130cc com The 1 Harley Davidson Rod...
2009 HARLEY DAVIDSON VRSCF Rod Muscle tires Michelin Tyre Selector
2009 Harley Davidson Rod Muscle Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 17, 2018 | 2009 Harley Davidson VRSCF VRod Muscle

1 Answer

My harley wont start


Key fob MUST be present near bike!
1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual.
2. With an assigned FOB present, turn IGN key ON - OFF - ON - OFF - ON
3. Press Left turn signal switch 3 times.
4. Press Right turn signal switch one time and release.
*Turn signals will flash 3 times. Current PIN will appear in the odometer. The first digit will be flashing.
TO ENTER NEW PIN:
5. Enter first digit (a) of the new PIN by pressing left turn signal (a) times.
6. Press right turn signal 1 time and release.
*The new digit (a) will replace the current in the odometer window.
7. Enter second digit (b) of the new PIN by pressing left turn signal switch (b) times.
8. Press right turn signal 1 time and release.
*The new digit will replace the current in odometer window.
9. Enter the third digit (c) of the new PIN by pressing left turn signal (c) times.
10. Press the right turn switch 1 time and release.
*The new digit (c) will replace the current in the odometer window.
11. Enter forth digit (d) of the new PIN by pressing left turn signal switch (d) times.
12. Press the right turn switch 1 time and release.
13. Enter the fifth digit (e) of the new PIN by pressing left turn signal (e) times.
*The new digit (e) will replace the current in the odometer window.
14. Press the right turn switch 1 time and release.
15. Before the module rearms, turn ignition key to OFF.
* The odometer will return to mileage display.
**Turning the ignition to OFF stores the new pin in the module.



Using the Security Alarm PIN Override to Start Your Harley Davidson

1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window.
2. Enter the first digit of your PIN (a) by pressing the left turn signal switch (a) times.
3. Press the right turn signal switch 1 time to move to the next digit.
4. Enter the second digit of your PIN (b) by pressing the left turn signal switch (b) times.
5. Press the right turn signal switch 1 time to move to the next digit.
6. Enter the third digit of your PIN (c) by pressing the left turn signal switch (c) times.
7. Press the right turn signal switch 1 time to move to the next digit.
8. Enter the forth digit of your PIN (d) by pressing the left turn signal switch (d) times.
9. Press the right turn signal switch 1 time to move to the next digit.
10. Enter the fifth digit of your PIN (e) by pressing the left turn signal switch (e) times.
11. Press the right turn signal switch 1 time to move to the next digit.
12. Press the right turn signal switch one time and the security system alarm is turned off.

Aug 10, 2014 | 2011 Harley Davidson FLSTC Heritage...

1 Answer

How do you access trouble codes on 2003 harley davidson deuce?


With the newer HD Security Systems using proximity FOBs where the key FOB needs to be close to the bike to start, this is now more important then ever. If the battery in your FOB dies and you have not set your Harley Alram Override PIN Code, you will not be starting your bike. It is just as important for those with oler Harley Davidsons with the push button alarm FOB. It you set your alarm and the battery dies before you return to your bike, again you will not be starting the bike.

If you haven't set the PIN over ride for your HD security alarm system...do it now! Here's how you do it...

(To view how to deactivate the security system with the manual PIN code, see below.
)



Setting or Changing Your Security System Alarm Override PIN

Button less fobs (Smart FOB)


1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual.

2. With an assigned FOB present, turn IGN key ON - OFF - ON - OFF - ON

3. Press Left turn signal switch 3 times.

4. Press Right turn signal switch one time and release.
*Turn signals will flash 3 times. Current PIN will appear in the odometer. The first digit will be flashing.

5. Enter first digit (a) of the new PIN by pressing left turn signal (a) times.

6. Press right turn signal 1 time and release.
*The new digit (a) will replace the current in the odometer window.

7. Enter second digit (b) of the new PIN by pressing left turn signal switch (b) times.

8. Press right turn signal 1 time and release.
*The new digit will replace the current in odometer window.

9. Enter the third digit (c) of the new PIN by pressing left turn signal (c) times.

10. Press the right turn switch 1 time and release.
*The new digit (c) will replace the current in the odometer window.

11. Enter forth digit (d) of the new PIN by pressing left turn signal switch (d) times.

12. Press the right turn switch 1 time and release.

13. Enter the fifth digit (e) of the new PIN by pressing left turn signal (e) times.
*The new digit (e) will replace the current in the odometer window.

14. Press the right turn switch 1 time and release.

15. Before the module rearms, turn ignition key to OFF.
* The odometer will return to mileage display.
**Turning the ignition to OFF stores the new pin in the module.


Push Button fobs

1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual.

2. With an assigned FOB present, turn IGN key ON - OFF - ON - OFF - ON

3. Press Left turn signal switch 3 times.

4. Press button on fob twice
Current PIN will appear in the odometer. The first digit will be flashing.

5. Enter first digit of the new PIN by pressing left turn signal until the desired number appears.
Press button on fob twice to enter number.

6. Enter second digit of the new PIN by pressing left turn signal until the desired number appears.
Press button on fob twice to enter number.

7. Enter third digit of the new PIN by pressing left turn signal until the desired number appears.
Press button on fob twice to enter number.

8. Enter forth digit of the new PIN by pressing left turn signal until the desired number appears.
Press button on fob twice to enter number.

9. Enter fifth digit of the new PIN by pressing left turn signal until the desired number appears.
Press button on fob twice to enter number.

Turning the ignition to OFF stores the new security PIN.



Using the Security Alarm PIN Override to Start Your Harley Davidson

1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window.

2. Enter the first digit of your PIN (a) by pressing the left turn signal switch (a) times.

3. Press the right turn signal switch 1 time to move to the next digit.

4. Enter the second digit of your PIN (b) by pressing the left turn signal switch (b) times.

5. Press the right turn signal switch 1 time to move to the next digit.

6. Enter the third digit of your PIN (c) by pressing the left turn signal switch (c) times.

7. Press the right turn signal switch 1 time to move to the next digit.

8. Enter the forth digit of your PIN (d) by pressing the left turn signal switch (d) times.

9. Press the right turn signal switch 1 time to move to the next digit.

10. Enter the fifth digit of your PIN (e) by pressing the left turn signal switch (e) times.

11. Press the right turn signal switch 1 time to move to the next digit.

12. Press the right turn signal switch one time and the security system alarm is turned off.


May 20, 2014 | 2003 Harley Davidson FXSTDI Softail Deuce

1 Answer

2009 Harley Davidson VRSCF V-Rod Muscle fuse box location


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
2009 Harley Davidson VRSCF Rod Muscle fuse box location Google Search
Harley Davidson Rod VRSC Workshop Service Repair Manual 2009 $8 very cheap
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2009 Harley Davidson Rod Muscle Owner Manual
Instant Tech Relief To speak to me personally absolutely free

Sep 12, 2013 | 2009 Harley Davidson VRSCF VRod Muscle

1 Answer

How do i reset a pin number on a harley


With the fob present, turn IGN switch:
IGNITION-OFF-IGNITION-OFF-IGNITION
Press LEFT turn signal switch 3 TIMES
Press RIGHT turn signal switch 1 TIME and release
Turn signals will flash 3 times. Current PIN will appear in odometer. The first digit will be flashing.

If changing PIN, enter first digit (a) of new PIN by pressing LEFT signal switch (a) time(s) i.e., for the number 1, press one time. for the number 5, press 5 times.

Press RIGHT signal switch 1 TIME and release.
the new digit (a) will replace the current in odometer window.

Enter second digit (b) with LEFT signal switch.

Repeat until PIN is set.

Apr 16, 2013 | 2009 Harley Davidson FXD Dyna Super Glide

1 Answer

2009 VRSCF


Here's a quick take from the official H-D release. The wide, angular air-box cover and chopped tail section look as solid and smooth as billet and give the new V-Rod Muscle lines that are clean and powerful. The size of the massive 240 mm rear tire is accentuated by the new broad, clipped and clean rear fender. The combination stop/tail/turn LED light is tucked under the edge of the rear fender, and the side-mount license plate leaves the fender surface smooth and uncluttered. Front-end styling balances the rear, with a trimmed fender that's blacked out behind satin-finished inverted forks and LED turn signals integrated into the mirror stems. The radiator shrouds are restyled and color-matched to the rest of the bodywork, while the new airbox side covers incorporate air scoop inlets covered with woven wire mesh. The silver five-spoke cast aluminum front and rear wheels are a new design for the V-Rod line.

Jul 26, 2012 | 2009 Harley Davidson VRSCF VRod Muscle

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

932 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Gar
Gar

Level 2 Expert

384 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5914 Answers

Mike

Level 3 Expert

4357 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...