Question about 2003 Yamaha YZ 125

1 Answer

Wont stay running with out the choke on

New to 2 stroke it rus fine with the choke on but as soon as i shut it off it stalls out , what kind of oil should i use for the mix and crank case

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

It sounds like you need a carb clean performed. the idle cuciut jet is probably dirty and that is the jet that supplies gas to the combustion process at idle rpm's. when you have the choke pulled out it is adding fuel and air so when you shut off the choke the fuel supply goes away. for the oils use yamalube 2 stroke oil for pre-mix and 10w -30 gear oil for your tranny.

Posted on Dec 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda nsr250 mc18


The NSR is a 2 stroke, so it needs 2 stroke oil as well as petrol. This is the reason they are known as "Stinkwheels". If the engine is run without oil in the mix it will seize. As the oil provides lubrication to the moving parts. You should also check the spark plugs are clean, they can oil up in a 2 stroke, especially if the engine is used a lot at low revs.

May 03, 2013 | Motorcycles

1 Answer

I have a 1985 honda goldwing gl 1200 aspencade i can start the bike it runs fine as soon as it get warm the oil light in dash comes on and motor shuts off i have change oil and filter and the oil pressure...


Hi Most likely your engine shut off first then the light goes on as soon as the engine oil pressure dropped sounds like you have a carb problem and the motorcycle is running on the choke circuit. then it dies after the choke is turned off.

Oct 24, 2012 | Motorcycles

1 Answer

Scooter starts but turns off


Hi, Domagoj and the usual suspects are:
1. Idle speed improperly adjusted.
2. Inlet system air leak.
3. Leaking accelerator pump.
4. Loose low-speed jet.
5. Plugged low-speed jet.
6. Contaminated or plugged low-speed circuit.
7. Enrichner valve is not seated or leaking.
For more information about your issue and free downloads that you will need please visit the websites below. Good luck and have nice a day.
Scooter Troubleshooting Scooter won run All about Scooters
2 Stroke Carburetor Rebuild Rm 250 Part 1
Two Stroke Scooter ATV Carburetor Settings And Adjustments 1of4 Basics...
http://absolutelyscooters.net/service-manuals.html
CPI Scooter Parts Racing Planet USA

Apr 26, 2012 | Cpi GTR 50 Motorcycles

1 Answer

Why does my dt125r 2001 stall at high revs


Drain the tank and switch to a 32 /1 mix. I take it you have disconnected the oil feed to the carb from the 2 stroke tank, if not then your mix contains too much oil. Only switch to 32 / 1 if the oil tank has been disconnected. I hope this helps.

Dec 18, 2011 | Yamaha DT 125 X Motorcycles

1 Answer

I have yamaha aerox and wont start


Have you been using 2 stroke oil in the oil tank? A lot of new riders haven't had this explained. A neighbour used engine oil and has now got to strip and refurbish the engine. A 2 stroke engine mixes oil with the petrol to lubricate the crank and con rod on the induction cycle. If you use engine oil, it carbonises in the engine due to the extremely high temperatures on the underside of the piston and aroud the bearing surfaces of the crank. It will run "ok" for a short while on this oil, but will eventually kill your engine. Also on 2 strokes the exhaust system needs regular cleaning to remove "coke" which is burnt oil in the form of a sludge. 2 strokes use exhaust tuning to improve performance and efficiency, so it may need a clean. This is the best advise I can offer with the information supplied, and also the most obvious. Just one other thing - when you turn the engine over do you get a spark? It could be the coil, if the rest is good. Sorry I can't be of more assistance, I hope this give you an idea of where to go from here.

Nov 22, 2011 | Yamaha Motorcycles

2 Answers

My 1994 xr6004 has good compression and has had a new top end, it runs awesome and kicks over fairly easy when cold and runs/drives great, but as soon as it warms up and you shut it off or it stalls out,...


The fuel in the carburetor float chambers is boiling while it sits, and flooding the engine. If it has a fuel petcock turn that off, and let the bike stop through fuel starvation. Then there will be no fuel in there to boil.

Jun 15, 2010 | 1994 Honda XR 600 R

1 Answer

2001 suzuki drz 400, spark seems good and fuel flows to the carb.wont stay idel or start with out the choke pulled out and as soon as i push the choke in it stalls


How old is your air filter, if more than 1000miles, try to change it first then check also fuel filter condition. Good?

Mar 25, 2010 | 2001 Suzuki DR-Z 400 SE

2 Answers

400 Eiger ATV, starts and runs fine, stalls the


If 2 stroke check crank seals, check plug cap for proper resistance,check for good fuel flow to carb.Spark should jump at least a 1/4" gap,NOT JUST the .030 or plug gap.

Sep 08, 2009 | 2004 Suzuki DR-Z 400 E

1 Answer

Clutch wont disengage properly


What kind of oil is in the crankcase? Wet clutches take a sprcial oil, noy motor oil. If oil is correct, Is the cable and release levers fully disengaging the clutch? There is an adjustment for the rod inside the clutcjh hub . That could be short stroking.

May 17, 2009 | 1985 Yamaha XJ 700 X Maxim

Not finding what you are looking for?
2003 Yamaha YZ 125 Logo

464 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

mikeuk

Level 2 Expert

61 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

D. E. Hev

Level 3 Expert

1132 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...