Question about 1997 kawasaki ZX-6R Ninja

1 Answer

AT 6000 TO 7000 RPM BIKE DONT PULL

IF I RIDE MY BIKE, AT 6000 TO 7000 RPM THE BIKE DONT WANT TO PULL. IF IT STANDS STILL IT REFS UP

Posted by on

  • 1 more comment 
  • neonfix Dec 07, 2008

    still same problem. if i drive my bike, from 6 to 7000 rpm is dont

    wantto pull, if you pull the clutch lever and revs it over 7000 rpm

    it runs wonderful. at 6 to 7000 the bike is jerking. could this be a valve problem and what is the valve settings, please.

  • Anonymous Mar 20, 2014

    have a flat spot between 5 and 6 thousand rpm when pulling need to find a diagram for the vacuum hoses on where they all run to . anything I have found has at least three different diagrams . hopefully it will take it out of my bike. thanks

  • Anonymous Mar 21, 2014

    have power up to 5000 rpm but then the bike will not pull any more

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi and welcome to FixYa,

Offhand, I would suspect an airleak on the airfilter box, most likely the seal between the air filter bottom housing to the mouth of the carb. Might as well check for a vacuum leak on the rubber coupling from the carb to the intake manifolds. Pls check for craks on the coupling wall. It would also be worth your time to check the mating of the rubber coupling to the carb as well as the clamps.

Good luck and Thank you for using FixYa. Happy Holidays.

Posted on Dec 07, 2008

  • Louie  Role
    Louie Role Dec 07, 2008

    It is not a valve problem.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why when I am riding my motorcycle and I pull the Clutch to gear down my motorcycle it cut off and take long to start back.


Are you saying that when you put the bike into gear to pull away from standing, the engine cuts out? If so, then check your side stand switch. It is there to cut the engine out if you try to ride off with your stand down. Your stand may be up but the switch may be telling the engine it is down.

Sep 23, 2015 | Motorcycles

1 Answer

My bike don't want to ref more then 9000 rpm


it sounds like the computer needs checking

Jul 03, 2014 | 2004 Honda CBR 600 RR

1 Answer

4 wheeler backfire on start


incorrect air fuel mixture or a leak check for damage to the intake boot or airbox

i need to know more about how its running at low mid and high rpm to help you troubleshoot and you need to check for leaks especiely the intake boot if the intake boot is leaking that will need to be fixed before running the bike asumeing that is ok or fixed run the bike listen to it at idle standing is it surgeing with a good fast acceleration off the line with you siting on the quad ? or just realy rough ticking over with little guts off the line ?

midrange rideing how does it feel is there a bwarrr noise as u accelorate hard or does the engine roar up fast

is it reaching a good top end with good pulling power or poor pulling power

are the backfires constant or mainly whyle slowing down from high revs

if all are effected but there are no leaks then it may be float / fuel level that needs ajustment fuel level in ur float bowel effects all stages of rpm low mid and high

A rich problem gets worse as the engine heats up.



A lean problem gets better as the engine heats up.



hope this helps if u dont fix it your self first try and do them little rpm backfire tests for me itl tell me a lot

Dec 05, 2012 | Yamaha Motorcycles

1 Answer

Recently went for a ride and everything was good. Made a stop, when I came out bike wouldnt start. turning the key everything was normal, rpm gauge spiked, lights turned on, fuel pump was heard. Went to...


Did you leave your motorcycle in gear when you turned it off? It sounds like the side stand safety switch is keeping the bike turned off. If my Suzuki is running and I pull in the clutch, with out raising the side stand, and I place the bike in gear with the side stand down, it will immediately shut off. The cycle is set up that way so you will not drive with your stand down and go out of control when you take your first left turn. If your cycle is not in neutral and your side stand is down, that would cause the condition you describe. If that is not the case start by inspecting the side stand safety switch and the clutch safety switch for proper operation.

Jun 24, 2011 | Suzuki GSX-R 750 F Motorcycles

2 Answers

Engine cuts out with clutch engaged.


idle adjust?
there SHOULD be an adjuster under the seat or gastank within easy reach. Clockwise to increase rpm, ccl to decrease rpm. idle around 1400rpm when engine is at normal operating temp. Good luck!

Aug 04, 2009 | 2002 Yamaha YZF-R1

1 Answer

Idols high when comming to a stop wont idol down


Sounds like you have either a carb with a sticky slide. Pull air box and look down carb throats while twisting throttle (assuming the bike is not EFI)

Jul 20, 2009 | 2003 Yamaha YZF 600 R thunder cat

1 Answer

Clutch not responding to leever


u are going to have to trust me on this one. put the bike on its center stand with the front wheel touching a wall.now with the rear wheel off the ground and the bike running in nutral.pull the clutch in and put it into 1 gear.Keeping the rear wheel off the ground .if u feel that u have skills. have a friend hold the front of the bike down .and run the bike throw the gears.u dont have to give it that much gas.your just looking to free up the clutch plates. p.s i promise u this will work. JUST BECAREFULL!!!

Mar 08, 2009 | 1990 Yamaha XJ 600

1 Answer

Suzuki bandit gsf250 not starting


Suzuki Bandit 250 1996 model has a ******* caburator, pl clean the caburator and ride daily,when you ride the bike pl continue the rpm level between 4 and 6, dont take suzuki brand again pl goto next time honda brand..honet... etc...................................

Jan 31, 2009 | 1992 Suzuki GSF 250 Bandit

Not finding what you are looking for?
1997 kawasaki ZX-6R Ninja Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

chris

Level 2 Expert

232 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...