Question about 2003 Suzuki TL 1000 R

1 Answer

Wireing new mirrors with LED lights to the exsting signals.

I have Suzuki TL1000R. I just bought new mirrors with LED lights, how can i wire them to the exsting signals.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

If the wires from the mirrors aren't long enough to reach the signal lights, extend the wires with similar guage wires long enought to reach the signal light wires. Make sure to make a good connection when lengthening by useing the same kind of connections that are used to connect your singnal light wires so that you can take your mirros off and disconnect them from right behind where you mount your mirros instead of haveing to disconnect them from way down by your signal lights wires. You can splice into the wires "positive and negitive" to where your signal lights plug into. DO NOT splice into the wires that come off when you remove your singnal lights. That way you dont have to splice and resplice when you have to replace signal light housings. Not that hard really.

Posted on Dec 05, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear wiring for suzuki tr1000s brake light and parking light problems after changing to led lights


there could be incompatibility when changing to LED lights as indicators need a current flow to operate
talk with a bike electrician as you may have to incorporate a ballast in the circuit to make the system work

Dec 18, 2016 | Suzuki Cars & Trucks

1 Answer

Install of led turn signal mirrors


Hi, Lester the mirrors should have come with instructions too bad, you can try googling the manufacturer for online instructions, anyways you need to splice them into the turn signal button wiring harness and you will need a load equalizer or diodes to maintain proper function of all TS lights for this scenario you will need your service/owners manual that has a wiring diagram in the back pages, if you can't find the first and best tool you ever bought for your Honda, despair not, for a mere $20 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.ctx700forum.com/forum/electrical/28593-led-mirrors.html
Honda CBR600rr Mirrors with Turn Signals Installation Step by Step...
Download Repair Manuals
http://www.partsfish.com/page/oem-parts-for-honda
Honda CTX700A Owner Manual

Aug 20, 2016 | 2014 Honda CTX 700N DCT ABS

1 Answer

2003 Suzuki AN 650 Burgman indicators intermittant


Hi, Jesse before testing any electrical component in the Turn Signal Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, especially "AGM" batteries, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Suzuki AN650 Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki http://mybikemanuals.com/suzuki
Suzuki Burgman 650
Suzuki Burgman Wikipedia

Oct 26, 2017 | 2003 Suzuki AN 650 Burgman

1 Answer

How to wire turn signal mirrors on 04 cavalier


Did you get them new? If so, there should be a schematic wiring diagram with them. You could also search the net. Google the model of your mirrors, and perhaps there will be site with the schematics. Normally, if it was me, I'd patch the parking lamp wire into the front marker lights, the tun signal wire right where it says, the turn signals, and the other is a ground which can be grounded to anywhere on the bare metal frame. Use your basic wiring skills. If you don't have any basic wiring skills, do some web research on it. You can solve this yourself, you just need some confidence and a little more knowledge.

Mar 28, 2014 | Cars & Trucks

1 Answer

Rear led turn signal problems


reverse the wires...led indicaters are sensitive to which way round they're wired in...problem is though that unless you change your flasher unit or wire in ballast resistors they are going to flash too fast anyway.

May 30, 2012 | Suzuki Motorcycles

1 Answer

Got a c11 and a c12 on my suzuki tl1000r what does it mean


c11 Camshaft position sensor or circuit malfunction The signal does not reach to ECM for more than 2 sec. after receiving the starter signal. The CMP sensor wiring and mechanical parts. (CMP sensor, rear intake cam pin, wiring/coupler connection) c12 Crankshaft position sensor or circuit malfunction The signal does not reach to ECM for more than 2 sec. after receiving the starter signal. The CKP sensor wiring and mechanical parts.(CKP sensor, wiring/coupler connection)

May 20, 2010 | 1999 Suzuki TL 1000 R

1 Answer

Wiring lights in side mirrors


Here is a link to a pdf (acrobat reader) file This pdf will show you how to run the proper wiring to your turn signal mirrors..
Cool upgrade!
Let me know how you like them after install.
K

Click here for pdf

May 30, 2009 | 2002 Ford F350 Super Duty DRW Reg. Cab

2 Answers

Installing led 2 wire lights


I had the same problem with my 1997 marauder the only way i have found to make them work is to hook up the LED signal lights into the stock signal lights i know it sounds crazy but what i have figured out is that it uses the stock bulbs like a fuse. all you have to do is take the headlight out just like you did when you wired in the LED lights and wire in your stock bulbs along with the LED lights once you have done this put the stock bulbs in the headlight assembly and put the headlight back in this should fix your problem at least it worked for me let me know if it works for you as well good luck

Mar 12, 2009 | 1999 Suzuki VZ 800 Marauder

1 Answer

I bought a mirror with LED lights. how can i wire them with the exsisting signals?


run the wire on the inside of the instrument panel and splice into existing front turnsignals

Dec 04, 2008 | 2003 Suzuki TL 1000 R

Not finding what you are looking for?
2003 Suzuki TL 1000 R Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...