Question about 2003 Suzuki TL 1000 R

1 Answer

I bought a mirror with LED lights. how can i wire them with the exsisting signals?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Run the wire on the inside of the instrument panel and splice into existing front turnsignals

Posted on Dec 19, 2008

2 Suggested Answers

johnnygixxer
  • 15 Answers

SOURCE: wireing new mirrors with LED lights to the exsting signals.

If the wires from the mirrors aren't long enough to reach the signal lights, extend the wires with similar guage wires long enought to reach the signal light wires. Make sure to make a good connection when lengthening by useing the same kind of connections that are used to connect your singnal light wires so that you can take your mirros off and disconnect them from right behind where you mount your mirros instead of haveing to disconnect them from way down by your signal lights wires. You can splice into the wires "positive and negitive" to where your signal lights plug into. DO NOT splice into the wires that come off when you remove your singnal lights. That way you dont have to splice and resplice when you have to replace signal light housings. Not that hard really.

Posted on Dec 05, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install of led turn signal mirrors


Hi, Lester the mirrors should have come with instructions too bad, you can try googling the manufacturer for online instructions, anyways you need to splice them into the turn signal button wiring harness and you will need a load equalizer or diodes to maintain proper function of all TS lights for this scenario you will need your service/owners manual that has a wiring diagram in the back pages, if you can't find the first and best tool you ever bought for your Honda, despair not, for a mere $20 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.ctx700forum.com/forum/electrical/28593-led-mirrors.html
Honda CBR600rr Mirrors with Turn Signals Installation Step by Step...
Download Repair Manuals
http://www.partsfish.com/page/oem-parts-for-honda
Honda CTX700A Owner Manual

Aug 20, 2016 | 2014 Honda CTX 700N DCT ABS

1 Answer

Rear led turn signal problems


reverse the wires...led indicaters are sensitive to which way round they're wired in...problem is though that unless you change your flasher unit or wire in ballast resistors they are going to flash too fast anyway.

May 30, 2012 | Suzuki Motorcycles

1 Answer

Bike started missing after installing mirrors wth turn signals in them and replaced turn signal bulbs on bike with singal filliment bulbs and cut the wires off taped them up that made the marker lights...


You might want to inspect the wires you tied into for the mirror signal lights.....did you cut into the wiring harness to make a connection? It sounds like you may have damaged a wire on the ignition circuit and it is shorting to ground...or you tied into the ignition power and the lights are drawing down the voltage on the circuit.

Mar 22, 2011 | Honda CBR 1000 RR Fireblade Motorcycles

1 Answer

LED Lights wont work


if the turn signal worked before try to change the wires to the led, make sure the positive is on the correct wire to the led.(switch them)
Also make sure fuse to turn signal is still good.

Apr 17, 2010 | 1982 Honda GL 1100 Innerstate Gold Wing

1 Answer

Hi i am changing the rear end of my 04 harley softail herritage, i have bought new turn signals and tail and stop light.my problem is this.the new turn signals have a green wire each ,one also has a blue...


Get a test light and stick the probe in the connector on the bike and clip the other end to a good ground. Turn on the key and run the turn signals, brake light and running light. Move the probe from hole to hole until you find the turn signal flash, the brake light and the running light. Obviously, the turn signals will flash, the brake light will go on and off when you hit the pedal, and the running light will stay on constantly. the three wires on the brake light are ground, brake and running light. Should be a simple matter to figure out which wires go where from here. If you are using digital lights, i.e. LED lights, the current only flows one way. As an example, if you hook up the turn signals and they don't work, reverse the wires.

Sep 03, 2009 | 2004 Harley Davidson FLSTC - FLSTCI...

1 Answer

Don't have any power except to my lights.


Sounds like a power wire that leads to your starter system may be shorted or broken, or another component may be bad, like a starter or relay. Put 12 volts DC directly to the starter and see if it turns over. If so, go to the power-in side of the starter relay (or solenoid) and see if there is 12vdc with the key on. You can use a volt meter or fluke meter set on volts, or a test light. If power exsists, you will need to check for the power signal that comes from the starter button. It is usually a red, sometimes with a white or black tracer, 18-gauge wire that connects to the relay. This power signal is what activates the relay. If power exsists, you will have to go to the starter switch and test for continuity, and keep tracing back from that point. If you just had the bike apart, its likely you may have forgotten to plug in a component or left a ground wire off somewhere.

Jun 11, 2009 | 2002 Suzuki GSX-R 1000

2 Answers

Replaced front signal lights with led mini marker lights


sounds like you have crossed the wiring,take apart and re try wiring 1 indicator side at a time this should clear the problem

May 19, 2009 | 1999 Honda VT 750 CD Shadow A.C.E. Deluxe

2 Answers

Installing led 2 wire lights


I had the same problem with my 1997 marauder the only way i have found to make them work is to hook up the LED signal lights into the stock signal lights i know it sounds crazy but what i have figured out is that it uses the stock bulbs like a fuse. all you have to do is take the headlight out just like you did when you wired in the LED lights and wire in your stock bulbs along with the LED lights once you have done this put the stock bulbs in the headlight assembly and put the headlight back in this should fix your problem at least it worked for me let me know if it works for you as well good luck

Mar 12, 2009 | 1999 Suzuki VZ 800 Marauder

1 Answer

Wireing new mirrors with LED lights to the exsting signals.


If the wires from the mirrors aren't long enough to reach the signal lights, extend the wires with similar guage wires long enought to reach the signal light wires. Make sure to make a good connection when lengthening by useing the same kind of connections that are used to connect your singnal light wires so that you can take your mirros off and disconnect them from right behind where you mount your mirros instead of haveing to disconnect them from way down by your signal lights wires. You can splice into the wires "positive and negitive" to where your signal lights plug into. DO NOT splice into the wires that come off when you remove your singnal lights. That way you dont have to splice and resplice when you have to replace signal light housings. Not that hard really.

Dec 04, 2008 | 2003 Suzuki TL 1000 R

Not finding what you are looking for?
2003 Suzuki TL 1000 R Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4497 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...